U-Boot SPL 2016.07-at13 (Jan 29 2018 - 13:11:53) Trying to boot from SPI U-Boot 2016.07-at13 (Jan 29 2018 - 13:11:53 +0900) CPU: Freescale i.MX7D rev1.2 at 996MHz CPU: Extended Commercial temperature grade (-20C to 105C) at 46C Reset cause: POR Watchdog enabled I2C: ready DRAM: 512 MiB Boot Source: QSPI Flash Board Type: Armadillo-IoT G3(0a000000) Revision: 0002 S/N: 2472 DRAM: 00001d05 XTAL: 00 MMC: FSL_SDHC: 0, FSL_SDHC: 1 SF: Detected N25Q64 with page size 256 Bytes, erase size 64 KiB, total 8 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Found PFUZE300! deviceid 0x30, revid 0x11 Net: FEC0 => => setenv mmcroot /dev/sda1 rootwait rw => boot switch to partitions #0, OK mmc1(part 0) is current device switch to partitions #0, OK mmc1(part 0) is current device reading boot.scr ** Unable to read file boot.scr ** reading boot.scr ** Unable to read file boot.scr ** reading uImage 10157672 bytes read in 249 ms (38.9 MiB/s) Booting from mmc ... reading armadillo_iotg_g3.dtb 54427 bytes read in 18 ms (2.9 MiB/s) ## Booting kernel from Legacy Image at 82000000 ... Image Name: Linux-3.14.79-at20 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 10157608 Bytes = 9.7 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 84800000 Booting using the fdt blob at 0x84800000 Loading Kernel Image ... OK Using Device Tree in place at 84800000, end 8481049a Starting kernel ... Booting Linux on physical CPU 0x0 Linux version 3.14.79-at20 (atmark@atde6) (gcc version 4.9.2 ( 4.9.2-10) ) #2 SMP PREEMPT Tue Jan 30 09:37:38 JST 2018 CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine model: Atmark-Techno Armadillo-IoT Gateway G3 Board cma: CMA: reserved 64 MiB at 9c000000 Memory policy: Data cache writealloc PERCPU: Embedded 8 pages/cpu @9bbb4000 s8576 r8192 d16000 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 Kernel command line: console=ttymxc4,115200 root=/dev/sda1 rootwait rw PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 433236K/524288K available (9080K kernel code, 536K rwdata, 8008K rodata, 2572K init, 448K bss, 91052K reserved, 0K highmem) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xa0800000 - 0xff000000 (1512 MB) lowmem : 0x80000000 - 0xa0000000 ( 512 MB) pkmap : 0x7fe00000 - 0x80000000 ( 2 MB) modules : 0x7f000000 - 0x7fe00000 ( 14 MB) .text : 0x80008000 - 0x810b84cc (17090 kB) .init : 0x810b9000 - 0x8133c180 (2573 kB) .data : 0x8133e000 - 0x813c43c0 ( 537 kB) .bss : 0x813c43cc - 0x8143468c ( 449 kB) SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Preemptible hierarchical RCU implementation. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 NR_IRQS:16 nr_irqs:16 16 Switching to timer-based delay loop sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655765682ns Architected cp15 timer(s) running at 8.00MHz (phys). sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2147483648000ns Ignoring duplicate/late registration of read_current_timer delay Console: colour dummy device 80x30 Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) Initializing cgroup subsys net_cls CPU: Testing write buffer coherency: ok /cpus/cpu@0 missing clock-frequency property /cpus/cpu@1 missing clock-frequency property CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x808a3ec0 - 0x808a3f18 CPU1: Booted secondary processor CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated (12.00 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 pinctrl core: initialized pinctrl subsystem regulator-dummy: no parameters NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations cpuidle: using governor ladder cpuidle: using governor menu Use WDOG1 as reset source GPIO line 13 (MCU_INTB) hogged as input GPIO line 43 (SVEN) hogged as output/high GPIO line 60 (LAN1_INT_N) hogged as input GPIO line 62 (LAN1_COMA_MODE) hogged as output/low GPIO line 113 (3G_IGT_3.3) hogged as output/high syscon 30340000.iomuxc-gpr: regmap [mem 0x30340000-0x3034ffff] registered syscon 30350000.ocotp-ctrl: regmap [mem 0x30350000-0x3035ffff] registered syscon 30360000.anatop: regmap [mem 0x30360000-0x3036ffff] registered vdd1p0d: 800 <--> 1200 mV at 1000 mV vdd1p2: 1100 <--> 1300 mV syscon 30390000.src: regmap [mem 0x30390000-0x3039ffff] registered DDR type is DDR3! prom_parse: Bad cell count for /regulators0/regulator@0 hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. hw-breakpoint: maximum watchpoint size is 8 bytes. imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver imx7d-pinctrl 30330000.iomuxc: Invalid fsl,pins property in node /soc/aips-bus@30000000/iomuxc@30330000/imx7d-sdb/uart1grp imx7d-pinctrl 30330000.iomuxc: Invalid fsl,pins property in node /soc/aips-bus@30000000/iomuxc@30330000/imx7d-sdb/uart2grp imx7d-pinctrl 30330000.iomuxc: Invalid fsl,pins property in node /soc/aips-bus@30000000/iomuxc@30330000/imx7d-sdb/ecspi1grp imx7d-pinctrl 30330000.iomuxc: Invalid fsl,pins property in node /soc/aips-bus@30000000/iomuxc@30330000/imx7d-sdb/ecspi2grp imx7d-pinctrl 30330000.iomuxc: initialized IMX pinctrl driver MU is ready for cross core communication! bio: create slab at 0 mxs-dma 33000000.dma-apbh: initialized USB_OTG1_VBUS: 5000 mV VDD_SD1: 3300 mV platform regulators0:pds6-power: Driver reg-fixed-voltage requests probe deferral vgaarb: loaded i2c-core: driver [max17135] using legacy suspend method i2c-core: driver [max17135] using legacy resume method SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb 30800000.aips-bus:usbphy_nop1 supply vcc not found, using dummy regulator 30800000.aips-bus:usbphy_nop2 supply vcc not found, using dummy regulator i2c i2c-0: IMX I2C adapter registered gpio_bmic 3-0014: version: 2.0 bmic_regulator 3-0016: version: 1.0 BMIC_VREF: 1710 <--> 3600 mV at 2991 mV i2c i2c-3: IMX I2C adapter registered Linux video capture interface: v2.00 pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered MIPI CSI2 driver module loaded Advanced Linux Sound Architecture Driver Initialized. Bluetooth: Core ver 2.18 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized cfg80211: Calling CRDA to update world regulatory domain armadillo_iotg_addon addon: Atmark Techno DI/DO/AD board detected at Add-On Module I/F 1(Rev 2, SerialNumber=2396). prom_parse: Bad cell count for /soc/aips-bus@30800000/ecspi@30830000/mcp3202@0 DIDOAD_VREF: 5000 mV armadillo_iotg_addon addon: No add-on expansion board detected at Add-On Module I/F 2. cold-reset pds6-cold-reset: Cannot get the regulator platform pds6-cold-reset: Driver cold-reset requests probe deferral Switched to clocksource arch_sys_counter NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 2, 16384 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. imx rpmsg driver is registered. Bus freq driver module loaded futex hash table entries: 512 (order: 3, 32768 bytes) VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.22) msgmni has been set to 974 io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) imx-sdma 30bd0000.sdma: no event needs to be remapped imx-sdma 30bd0000.sdma: loaded firmware 4.1 imx-sdma 30bd0000.sdma: initialized pfuze100-regulator 3-0009: Full layer: 1, Metal layer: 1 pfuze100-regulator 3-0009: FAB: 0, FIN: 0 pfuze100-regulator 3-0009: pfuze3000 found. SW1A: 700 <--> 1475 mV at 1100 mV SW1B: 700 <--> 1475 mV at 1000 mV SW2: 1500 <--> 1850 mV at 1800 mV SW3: 900 <--> 1650 mV at 1350 mV SWBST: 5000 <--> 5150 mV at 5000 mV VSNVS: 1000 <--> 3000 mV at 3000 mV VREFDDR: 750 mV VLDO1: 1800 <--> 3300 mV at 1800 mV VLDO2: 800 <--> 1550 mV at 1500 mV VCCSD: 2850 <--> 3300 mV at 3300 mV V33: 2850 <--> 3300 mV at 3300 mV VLDO3: 1800 <--> 3300 mV at 3300 mV VLDO4: 1800 <--> 3300 mV at 3300 mV 30a70000.serial: ttymxc4 at MMIO 0x30a70000 (irq = 62, base_baud = 1500000) is a IMX console [ttymxc4] enabled serial: Freescale lpuart driver imx sema4 driver is registered. [drm] Initialized drm 1.1.0 20060810 [drm] Initialized vivante 1.0.0 20120216 on minor 0 brd: module loaded loop: module loaded (hci_tty): inside hci_tty_init (hci_tty): allocated 248, 0 fsl-quadspi 30bb0000.qspi: Unsupported cmd 0x65 fsl-quadspi 30bb0000.qspi: Unsupported cmd 0x61 fsl-quadspi 30bb0000.qspi: Unsupported cmd 0x65 fsl-quadspi 30bb0000.qspi: n25q064 (8192 Kbytes) 3 ofpart partitions found on MTD device 30bb0000.qspi Creating 3 MTD partitions on "30bb0000.qspi": 0x000000000000-0x000000100000 : "bootloader" 0x000000100000-0x000000140000 : "license" 0x000000140000-0x000000800000 : "reserved" fsl-quadspi 30bb0000.qspi: QuadSPI SPI NOR flash driver spi_imx 30830000.ecspi: probed CAN device driver interface 30bf0000.ethernet supply phy not found, using dummy regulator pps pps0: new PPS source ptp0 libphy: fec_enet_mii_bus: probed fec 30bf0000.ethernet eth0: registered PHC device 0 PPP generic driver version 2.4.2 usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver cdc_eem usbcore: registered new interface driver sierra_net usbcore: registered new interface driver cdc_ncm usbcore: registered new interface driver qmi_wwan ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-mxc: Freescale On-Chip EHCI Host driver usbcore: registered new interface driver cdc_acm cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters usbcore: registered new interface driver cdc_wdm usbcore: registered new interface driver usb-storage usbcore: registered new interface driver usbserial usbcore: registered new interface driver usbserial_generic usbserial: USB Serial support registered for generic usbcore: registered new interface driver ftdi_sio usbserial: USB Serial support registered for FTDI USB Serial Device usbcore: registered new interface driver option usbserial: USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver sierra usbserial: USB Serial support registered for Sierra USB modem usbcore: registered new interface driver usb_serial_simple usbserial: USB Serial support registered for zio usbserial: USB Serial support registered for funsoft usbserial: USB Serial support registered for flashloader usbserial: USB Serial support registered for google usbserial: USB Serial support registered for vivopay usbserial: USB Serial support registered for moto_modem usbserial: USB Serial support registered for hp4x usbserial: USB Serial support registered for suunto usbserial: USB Serial support registered for siemens_mpi usb3503 3-0008: switched to HUB mode usb3503 3-0008: usb3503_probe: probed in hub mode 30b10200.usbmisc supply vbus-wakeup not found, using dummy regulator 30b20200.usbmisc supply vbus-wakeup not found, using dummy regulator 30b30200.usbmisc supply vbus-wakeup not found, using dummy regulator ci_hdrc ci_hdrc.0: EHCI Host Controller ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected 30b30000.usb supply vbus not found, using dummy regulator ci_hdrc ci_hdrc.1: EHCI Host Controller ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2 ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected mousedev: PS/2 mouse device common for all mice input: 30370000.snvs-pwrkey as /devices/soc/30000000.aips-bus/30370000.snvs-pwrkey/input/input0 snvs_pwrkey 30370000.snvs-pwrkey: i.MX snvs powerkey probed i2c-core: driver [isl29023] using legacy suspend method i2c-core: driver [isl29023] using legacy resume method bmic_rtc 3-0011: version: 1.1 bmic_rtc 3-0011: rtc core: registered bmic_rtc as rtc0 snvs_rtc 30370034.snvs-rtc-lp: rtc core: registered 30370034.snvs-rtc-l as rtc1 i2c /dev entries driver IR NEC protocol handler initialized IR RC5(x) protocol handler initialized IR RC6 protocol handler initialized IR JVC protocol handler initialized IR Sony protocol handler initialized IR RC5 (streamzap) protocol handler initialized IR SANYO protocol handler initialized IR MCE Keyboard/mouse protocol handler initialized usbcore: registered new interface driver uvcvideo USB Video Class driver (1.1.1) i2c-core: driver [mag3110] using legacy suspend method i2c-core: driver [mag3110] using legacy resume method bmic_thermal 3-0013: version: 1.0 imx2-wdt 30280000.wdog: timeout 10 sec (nowayout=0) Bluetooth: HCI UART driver ver 2.2 Bluetooth: HCI H4 protocol initialized Bluetooth: HCI BCSP protocol initialized Bluetooth: HCILL protocol initialized Bluetooth: HCIATH3K protocol initialized usbcore: registered new interface driver bcm203x usbcore: registered new interface driver btusb usbcore: registered new interface driver ath3k sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper sdhci-esdhc-imx 30b40000.usdhc: Got CD GPIO #128. sdhci-esdhc-imx 30b40000.usdhc: Got WP GPIO #129. mmc0: no vqmmc regulator found mmc0: SDHCI controller on 30b40000.usdhc [30b40000.usdhc] using ADMA sdhci-esdhc-imx 30b60000.usdhc: allocated mmc-pwrseq sdhci-esdhc-imx 30b60000.usdhc: could not get ultra high speed state, work on normal mode mmc2: no vqmmc regulator found mmc2: no vmmc regulator found usb 2-1: new high-speed USB device number 2 using ci_hdrc mmc2: SDHCI controller on 30b60000.usdhc [30b60000.usdhc] using ADMA caam 30900000.caam: Instantiated RNG4 SH0 mmc2: BKOPS_EN bit is not set caam 30900000.caam: Instantiated RNG4 SH1 caam 30900000.caam: device ID = 0x0a160300 (Era 8) caam 30900000.caam: job rings = 3, qi = 0 mmc2: new high speed DDR MMC card at address 0001 mmcblk2: mmc2:0001 Q2J55L 3.56 GiB mmcblk2boot0: mmc2:0001 Q2J55L partition 1 2.00 MiB mmcblk2boot1: mmc2:0001 Q2J55L partition 2 2.00 MiB mmcblk2rpmb: mmc2:0001 Q2J55L partition 3 4.00 MiB mmcblk2: p1 p2 p3 mmcblk2boot1: unknown partition table mmcblk2boot0: unknown partition table hub 2-1:1.0: USB hub found hub 2-1:1.0: 3 ports detected caam algorithms registered in /proc/crypto hmac-sha1-caam alg registration failed sha1-caam alg registration failed hmac-sha224-caam alg registration failed sha224-caam alg registration failed hmac-sha256-caam alg registration failed sha256-caam alg registration failed hmac-md5-caam alg registration failed md5-caam alg registration failed xcbc-aes-caam alg registration failed xcbc-aes-caam alg registration failed caam_jr 30901000.jr0: registering rng-caam snvs-secvio 30370000.caam-snvs: violation handlers armed - non-secure state usbcore: registered new interface driver usbhid usbhid: USB HID core driver usbcore: registered new interface driver r8712u bmic_adc 3-0012: version: 1.0 coresight-tmc 30086000.etr: TMC initialized coresight-tmc 30084000.etf: TMC initialized coresight-tpiu 30087000.tpiu: TPIU initialized coresight-funnel 30083000.funnel: FUNNEL initialized coresight-funnel 30041000.funnel: FUNNEL initialized coresight-replicator replicator: REPLICATOR initialized coresight-etm3x 3007c000.etm: ETM initialized coresight-etm3x 3007d000.etm: ETM initialized usbcore: registered new interface driver snd-usb-audio NET: Registered protocol family 26 Netfilter messages via NETLINK v0.30. nfnl_acct: registering with nfnetlink. nf_conntrack version 0.5.0 (7793 buckets, 31172 max) ctnetlink v0.93: registering with nfnetlink. nf_tables: (c) 2007-2009 Patrick McHardy nf_tables_compat: (c) 2012 Pablo Neira Ayuso xt_time: kernel timezone is -0000 ipip: IPv4 over IPv4 tunneling driver gre: GRE over IPv4 demultiplexor driver ip_gre: GRE over IPv4 tunneling driver ip_tables: (C) 2000-2006 Netfilter Core Team ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully arp_tables: (C) 2002 David S. Miller TCP: cubic registered Initializing XFRM netlink socket NET: Registered protocol family 10 mip6: Mobile IPv6 ip6_tables: (C) 2000-2006 Netfilter Core Team sit: IPv6 over IPv4 tunneling driver ip6_gre: GRE over IPv6 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 Bridge firewalling registered can: controller area network core (rev 20120528 abi 9) NET: Registered protocol family 29 can: raw protocol (rev 20120528) can: broadcast manager protocol (rev 20120528 t) can: netlink gateway (rev 20130117) max_hops=1 Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.11 Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: BNEP socket layer initialized Bluetooth: HIDP (Human Interface Emulation) ver 1.2 usb 1-1: new high-speed USB device number 2 using ci_hdrc Bluetooth: HIDP socket layer initialized 8021q: 802.1Q VLAN Support v1.8 Key type dns_resolver registered ThumbEE CPU extension supported. usb-storage 1-1:1.0: USB Mass Storage device detected scsi0 : usb-storage 1-1:1.0 imx6q-pcie 33800000.pcie: phy link never came up imx6q-pcie 33800000.pcie: Failed to bring link up! imx6q-pcie 33800000.pcie: failed to initialize host imx6q-pcie: probe of 33800000.pcie failed with error -22 VDD_SD1: disabling regulator-dummy: disabling imx mcc test is registered. 3G_POWER_EN: 3800 mV input: gpio-keys as /devices/gpio-keys/input/input1 bmic_rtc 3-0011: setting system clock to 2018-02-15 04:04:34 UTC (1518667474) ALSA device list: No soundcards found. Warning: unable to open an initial console. Freeing unused kernel memory: 2572K (810b9000 - 8133c000) systemd-udevd[155]: starting version 215 random: systemd-udevd: uninitialized urandom read (16 bytes read, 34 bits of entropy available) scsi 0:0:0:0: Direct-Access General USB Flash Disk 1.0 PQ: 0 ANSI: 2 sd 0:0:0:0: [sda] 7831552 512-byte logical blocks: (4.00 GB/3.73 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] No Caching mode page found sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] No Caching mode page found sd 0:0:0:0: [sda] Assuming drive cache: write through sda: sda1 sd 0:0:0:0: [sda] No Caching mode page found sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] Attached SCSI removable disk EXT4-fs (sda1): recovery complete EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) EXT3-fs (mmcblk2p2): error: couldn't mount because of unsupported optional features (240) EXT2-fs (mmcblk2p2): error: couldn't mount because of unsupported optional features (240) EXT4-fs (mmcblk2p2): mounted filesystem with ordered data mode. Opts: (null) random: nonblocking pool is initialized usb 2-1.2: new high-speed USB device number 3 using ci_hdrc option 2-1.2:1.0: GSM modem (1-port) converter detected usb 2-1.2: GSM modem (1-port) converter now attached to ttyUSB0 option 2-1.2:1.1: GSM modem (1-port) converter detected usb 2-1.2: GSM modem (1-port) converter now attached to ttyUSB1 option 2-1.2:1.2: GSM modem (1-port) converter detected usb 2-1.2: GSM modem (1-port) converter now attached to ttyUSB2 option 2-1.2:1.3: GSM modem (1-port) converter detected usb 2-1.2: GSM modem (1-port) converter now attached to ttyUSB3 option 2-1.2:1.4: GSM modem (1-port) converter detected usb 2-1.2: GSM modem (1-port) converter now attached to ttyUSB4 qmi_wwan 2-1.2:1.5: cdc-wdm0: USB WDM device qmi_wwan 2-1.2:1.5 wwan0: register 'qmi_wwan' at usb-ci_hdrc.1-1.2, WWAN/QMI device, d2:a5:f8:ca:da:89 Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000000 CPU1: stopping CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.14.79-at20 #2 [<800157c8>] (unwind_backtrace) from [<8001184c>] (show_stack+0x10/0x14) [<8001184c>] (show_stack) from [<8089d068>] (dump_stack+0x84/0x98) [<8089d068>] (dump_stack) from [<80014710>] (handle_IPI+0x144/0x158) [<80014710>] (handle_IPI) from [<80008598>] (gic_handle_irq+0x58/0x5c) [<80008598>] (gic_handle_irq) from [<80012340>] (__irq_svc+0x40/0x70) Exception stack(0x980edf58 to 0x980edfa0) df40: 980edfa0 3b9aca00 df60: 60a01587 00000008 00000002 9bbbd0d0 2e834e0c 00000008 813541fc 9bbbd0d4 df80: 980ec000 00000000 00000018 980edfa0 00000008 80567a28 00000013 ffffffff [<80012340>] (__irq_svc) from [<80567a28>] (cpuidle_enter_state+0x54/0xec) [<80567a28>] (cpuidle_enter_state) from [<80567bc0>] (cpuidle_idle_call+0x100/0x154) [<80567bc0>] (cpuidle_idle_call) from [<8000f17c>] (arch_cpu_idle+0x8/0x44) [<8000f17c>] (arch_cpu_idle) from [<8006efe8>] (cpu_startup_entry+0x100/0x14c) [<8006efe8>] (cpu_startup_entry) from [<80008624>] (__enable_mmu+0x0/0x1c) ------------[ cut here ]------------ WARNING: CPU: 0 PID: 1 at kernel/time/tick-broadcast.c:604 tick_handle_oneshot_broadcast+0x1ac/0x1c8() Modules linked in: CPU: 0 PID: 1 Comm: sh Not tainted 3.14.79-at20 #2 [<800157c8>] (unwind_backtrace) from [<8001184c>] (show_stack+0x10/0x14) [<8001184c>] (show_stack) from [<8089d068>] (dump_stack+0x84/0x98) [<8089d068>] (dump_stack) from [<80034600>] (warn_slowpath_common+0x70/0x8c) [<80034600>] (warn_slowpath_common) from [<800346b8>] (warn_slowpath_null+0x1c/0x24) [<800346b8>] (warn_slowpath_null) from [<8008237c>] (tick_handle_oneshot_broadcast+0x1ac/0x1c8) [<8008237c>] (tick_handle_oneshot_broadcast) from [<8001e67c>] (mxc_timer_interrupt+0x2c/0x34) [<8001e67c>] (mxc_timer_interrupt) from [<8006f8f8>] (handle_irq_event_percpu+0x50/0x180) [<8006f8f8>] (handle_irq_event_percpu) from [<8006fa64>] (handle_irq_event+0x3c/0x5c) [<8006fa64>] (handle_irq_event) from [<800728d0>] (handle_fasteoi_irq+0x84/0x14c) [<800728d0>] (handle_fasteoi_irq) from [<8006f070>] (generic_handle_irq+0x2c/0x3c) [<8006f070>] (generic_handle_irq) from [<8000ee4c>] (handle_IRQ+0x40/0x90) [<8000ee4c>] (handle_IRQ) from [<8000856c>] (gic_handle_irq+0x2c/0x5c) [<8000856c>] (gic_handle_irq) from [<80012340>] (__irq_svc+0x40/0x70) Exception stack(0x980bfdf8 to 0x980bfe40) fde0: 00000000 00400104 fe00: 813c6f80 00000000 00000282 00000080 0000a458 00006a98 980be000 813c6af0 fe20: 986d0ab8 00000000 805d7f94 980bfe40 800385ec 800385fc 20030113 ffffffff [<80012340>] (__irq_svc) from [<800385fc>] (__do_softirq+0xc8/0x248) [<800385fc>] (__do_softirq) from [<80038a3c>] (irq_exit+0xb8/0xf4) [<80038a3c>] (irq_exit) from [<8000ee50>] (handle_IRQ+0x44/0x90) [<8000ee50>] (handle_IRQ) from [<8000856c>] (gic_handle_irq+0x2c/0x5c) [<8000856c>] (gic_handle_irq) from [<80012340>] (__irq_svc+0x40/0x70) Exception stack(0x980bfec8 to 0x980bff10) fec0: 00000001 00000000 00000001 00000000 813c6af0 980c8000 fee0: 980cc000 00000000 00000000 813c6af0 986d0ab8 00000000 00000000 980bff10 ff00: 808a360c 8089ad6c 60030013 ffffffff [<80012340>] (__irq_svc) from [<8089ad6c>] (panic+0x164/0x1bc) [<8089ad6c>] (panic) from [<80035fd8>] (complete_and_exit+0x0/0x1c) [<80035fd8>] (complete_and_exit) from [<00000001>] (0x1) ---[ end trace d91834c3ae3ed99b ]---