U-Boot 2020.04-at16 (Jun 28 2023 - 16:16:51 +0900) CPU: i.MX6ULL rev1.1 at 396 MHz Model: Atmark Techno Armadillo-600 Series DRAM: 512 MiB setup_rtc_disarm_alarm: Can't find bus WDT: Started with servicing (10s timeout) PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11 MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... *** Warning - bad CRC, using default environment In: mxc_serial Out: mxc_serial Err: mxc_serial switch to partitions #0, OK mmc1 is current device flash target is MMC:1 Net: Warning: ethernet@2188000 using MAC address from ROM eth0: ethernet@2188000 Fastboot: Normal Saving Environment to MMC... Writing to redundant MMC(1)... OK Normal Boot => setenv optargs => boot switch to partitions #0, OK mmc1 is current device 6861600 bytes read in 309 ms (21.2 MiB/s) Booting from mmc ... 36414 bytes read in 19 ms (1.8 MiB/s) Loading fdt boot/armadillo-610.dtb 48 bytes read in 14 ms (2.9 KiB/s) not found!t overlay armadillo-610-onboard-usdhc2.dtbo ## Booting kernel from Legacy Image at 80800000 ... Image Name: Linux-5.10.185-1-at Created: 2023-07-07 7:06:17 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 6861536 Bytes = 6.5 MiB Load Address: 82000000 Entry Point: 82000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83500000 Booting using the fdt blob at 0x83500000 Loading Kernel Image Loading Device Tree to 9ef1e000, end 9ef49fff ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.185-1-at (builder@026b4ada4f0b) (armv7-alpine-linux-musleabihf-gcc (Alpine 12.2.1_git20220924-r4) 12.2.1 20220924, GNU ld (GNU Binutils) 2.39) #2-Alpine Fri Jul 7 07:08:18 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Atmark Techno Armadillo-610 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9f000000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920 [ 0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk1p1 rootwait ro [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] Memory: 489476K/524288K available (8192K kernel code, 689K rwdata, 2416K rodata, 1024K init, 231K bss, 18428K reserved, 16384K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000017] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000060] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.002190] Console: colour dummy device 80x30 [ 0.002268] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.002311] pid_max: default: 32768 minimum: 301 [ 0.004316] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.004360] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.007724] CPU: Testing write buffer coherency: ok [ 0.009635] Setting up static identity map for 0x80100000 - 0x80100060 [ 0.010922] devtmpfs: initialized [ 0.028275] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.028858] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.028910] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.030633] pinctrl core: initialized pinctrl subsystem [ 0.030822] regulator: Failed to create debugfs directory [ 0.031551] regulator-dummy: Failed to create debugfs directory [ 0.034191] NET: Registered protocol family 16 [ 0.036535] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.039039] thermal_sys: Registered thermal governor 'step_wise' [ 0.129113] vdd3p0: Failed to create debugfs directory [ 0.129187] vdd3p0: supplied by regulator-dummy [ 0.136434] cpu: supplied by regulator-dummy [ 0.136974] cpu: Failed to create debugfs directory [ 0.144154] vddsoc: supplied by regulator-dummy [ 0.144621] vddsoc: Failed to create debugfs directory [ 0.297406] failed to find ocotp node [ 0.299060] imx6ul-pinctrl 20e0000.pinctrl: no fsl,pins and pins property in node /soc/bus@2000000/pinctrl@20e0000/extgpioledsgrp [ 0.299249] imx6ul-pinctrl 20e0000.pinctrl: no fsl,pins and pins property in node /soc/bus@2000000/pinctrl@20e0000/lcd70ext_l00hoggrp [ 0.299361] imx6ul-pinctrl 20e0000.pinctrl: no fsl,pins and pins property in node /soc/bus@2000000/pinctrl@20e0000/expansion_interfacehoggrp [ 0.299413] imx6ul-pinctrl 20e0000.pinctrl: no fsl,pins and pins property in node /soc/bus@2000000/pinctrl@20e0000/gpioampgrp [ 0.299457] imx6ul-pinctrl 20e0000.pinctrl: no fsl,pins and pins property in node /soc/bus@2000000/pinctrl@20e0000/gpiocon13bgrp [ 0.299481] imx6ul-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 0.300164] imx6ul-pinctrl 2290000.iomuxc-snvs: no fsl,pins and pins property in node /soc/bus@2200000/iomuxc-snvs@2290000/expansioninterfacehogsnvsgrp [ 0.300202] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver [ 0.321346] raid6: skip pq benchmark and using algorithm neonx8 [ 0.321387] raid6: using neon recovery algorithm [ 0.325979] gpio-45 (SWITCH_LCD_DATA18): hogged as output/high [ 0.326040] gpio-47 (SE_RST_N): hogged as output/high [ 0.343353] VDD_ONBOARD_SD2: Failed to create debugfs directory [ 0.344879] SCSI subsystem initialized [ 0.345547] usbcore: registered new interface driver usbfs [ 0.345687] usbcore: registered new interface driver hub [ 0.345798] usbcore: registered new device driver usb [ 0.348489] i2c i2c-0: IMX I2C adapter registered [ 0.349940] i2c i2c-2: IMX I2C adapter registered [ 0.350947] Advanced Linux Sound Architecture Driver Initialized. [ 0.354557] clocksource: Switched to clocksource mxc_timer1 [ 0.378858] NET: Registered protocol family 2 [ 0.379489] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.381484] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.381718] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.381841] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.381950] TCP: Hash tables configured (established 4096 bind 4096) [ 0.382206] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.382267] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.382822] NET: Registered protocol family 1 [ 0.382919] NET: Registered protocol family 44 [ 0.384998] Initialise system trusted keyrings [ 0.385501] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.398963] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.400566] NET: Registered protocol family 38 [ 0.400613] xor: measuring software checksum speed [ 0.419898] arm4regs : 514 MB/sec [ 0.449989] 8regs : 327 MB/sec [ 0.480169] 32regs : 326 MB/sec [ 0.498279] neon : 545 MB/sec [ 0.498298] xor: using function: neon (545 MB/sec) [ 0.498334] Key type asymmetric registered [ 0.498357] Asymmetric key parser 'x509' registered [ 0.498482] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 0.512329] imx-sdma 20ec000.sdma: firmware found. [ 0.512825] imx-sdma 20ec000.sdma: loaded firmware 3.5 [ 0.513937] pfuze100-regulator 0-0008: Full layer: 1, Metal layer: 1 [ 0.514622] pfuze100-regulator 0-0008: FAB: 0, FIN: 0 [ 0.514653] pfuze100-regulator 0-0008: pfuze3000 found. [ 0.515745] SW1A: Failed to create debugfs directory [ 0.516828] SW1B: Failed to create debugfs directory [ 0.517783] SW2: Failed to create debugfs directory [ 0.518794] SW3: Failed to create debugfs directory [ 0.520444] SWBST: Failed to create debugfs directory [ 0.521567] VSNVS: Failed to create debugfs directory [ 0.521917] VREFDDR: Failed to create debugfs directory [ 0.522945] VLDO1: Failed to create debugfs directory [ 0.523881] VLDO2: Failed to create debugfs directory [ 0.524920] VCCSD: Failed to create debugfs directory [ 0.525863] V33: Failed to create debugfs directory [ 0.526883] VLDO3: Failed to create debugfs directory [ 0.528077] VLDO4: Failed to create debugfs directory [ 0.529614] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 20, base_baud = 5000000) is a IMX [ 1.233456] printk: console [ttymxc0] enabled [ 1.273165] imx_rngc 2284000.rng: Freescale RNGB registered (HW revision 2.129) [ 1.282602] random: crng init done [ 1.286773] zram: Added device: zram0 [ 1.293289] tun: Universal TUN/TAP device driver, 1.6 [ 1.338456] PPP generic driver version 2.4.2 [ 1.343385] usbcore: registered new interface driver awl13 [ 1.348981] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.355578] ehci-mxc: Freescale On-Chip EHCI Host driver [ 1.361245] usbcore: registered new interface driver cdc_acm [ 1.366998] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.375185] usbcore: registered new interface driver usb-storage [ 1.381388] usbcore: registered new interface driver usbserial_generic [ 1.388046] usbserial: USB Serial support registered for generic [ 1.394136] usbcore: registered new interface driver cp210x [ 1.399815] usbserial: USB Serial support registered for cp210x [ 1.405896] usbcore: registered new interface driver ftdi_sio [ 1.411719] usbserial: USB Serial support registered for FTDI USB Serial Device [ 1.419153] usbcore: registered new interface driver mxuport [ 1.424917] usbserial: USB Serial support registered for MOXA UPort [ 1.431285] usbcore: registered new interface driver pl2303 [ 1.436970] usbserial: USB Serial support registered for pl2303 [ 1.448680] snvs_rtc 20cc000.snvs:snvs-rtc-lp: registered as rtc0 [ 1.454972] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01T00:00:00 UTC (0) [ 1.464237] i2c /dev entries driver [ 1.472337] sdhci: Secure Digital Host Controller Interface driver [ 1.478651] sdhci: Copyright(c) Pierre Ossman [ 1.483031] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.497269] usbcore: registered new interface driver usbhid [ 1.502923] usbhid: USB HID core driver [ 1.516344] NET: Registered protocol family 10 [ 1.527635] Segment Routing with IPv6 [ 1.531935] NET: Registered protocol family 17 [ 1.536626] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.549748] mmc0: SDHCI controller on 2190000.mmc [2190000.mmc] using ADMA [ 1.557573] Key type dns_resolver registered [ 1.563985] ThumbEE CPU extension supported. [ 1.568478] Loading compiled-in X.509 certificates [ 1.587039] Loaded X.509 cert 'Build time autogenerated kernel key: ef0a75e761f944bf504f6656dfc5ab9b23e4e1dc' [ 1.599577] Btrfs loaded, crc32c=crc32c-generic [ 1.605850] imx_thermal 20c8000.anatop:tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C [ 1.618781] ALSA device list: [ 1.621783] No soundcards found. [ 1.625856] Waiting for root device /dev/mmcblk1p1... [ 1.710926] mmc0: new DDR MMC card at address 0001 [ 1.716844] mmcblk0: mmc0:0001 S0J35A 3.53 GiB [ 1.721899] mmcblk0boot0: mmc0:0001 S0J35A partition 1 31.5 MiB [ 1.728479] mmcblk0boot1: mmc0:0001 S0J35A partition 2 31.5 MiB [ 1.734934] mmcblk0gp0: mmc0:0001 S0J35A partition 4 8.00 MiB [ 1.741197] mmcblk0gp1: mmc0:0001 S0J35A partition 5 8.00 MiB [ 1.747577] mmcblk0gp2: mmc0:0001 S0J35A partition 6 8.00 MiB [ 1.753807] mmcblk0gp3: mmc0:0001 S0J35A partition 7 8.00 MiB [ 1.760048] mmcblk0rpmb: mmc0:0001 S0J35A partition 3 4.00 MiB, chardev (249:0) [ 1.776345] mmcblk0: p1 p2 p3