U-Boot 2016.07-at23 (Nov 01 2023 - 14:36:48 +0900) CPU: Freescale i.MX7D rev1.3 at 996MHz CPU: Extended Commercial temperature grade (-20C to 105C) at 41C Reset cause: POR Watchdog enabled I2C: ready DRAM: 512 MiB Boot Source: SD Board Type: Armadillo-X1(0a100000) Revision: 0002 S/N: 49746 DRAM: 00001d05 XTAL: 00 X1 Addon EEPROM Detect Atmark Techno Ext SD Slot Detect MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... *** Warning - bad CRC, using default environment Failed (-5) Loading Environment from MMC... *** Warning - bad CRC, using default environment Failed (-5) In: serial Out: serial Err: serial Found PFUZE300! deviceid 0x30, revid 0x11 Net: FEC0 => boot switch to partitions #0, OK mmc0 is current device switch to partitions #0, OK mmc0 is current device reading boot.scr ** Unable to read file boot.scr ** ** Invalid partition 3 ** reading uImage 12914928 bytes read in 673 ms (18.3 MiB/s) Booting from mmc ... reading armadillo_x1.dtb 53539 bytes read in 18 ms (2.8 MiB/s) ## Booting kernel from Legacy Image at 82000000 ... Image Name: Linux-4.9.133-at30 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 12914864 Bytes = 12.3 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 84800000 Booting using the fdt blob at 0x84800000 Loading Kernel Image ... OK Using Device Tree in place at 84800000, end 84810122 Starting kernel ... Booting Linux on physical CPU 0x0 Linux version 4.9.133-at30 (atmark@atde8) (gcc version 8.3.0 (Debian 8.3.0-2) ) #6 SMP PREEMPT Sat Nov 18 18:59:47 JST 2023 CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d CPU: div instructions available: patching division code CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache OF: fdt:Machine model: Atmark-Techno Armadillo-X1 Board Reserved memory: created CMA memory pool at 0x8c000000, size 320 MiB OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool Memory policy: Data cache writealloc percpu: Embedded 14 pages/cpu @8ba9b000 s26636 r8192 d22516 u57344 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129920 Kernel command line: console=ttymxc4,115200 root=/dev/mmcblk0p2 rootwait rw PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 166904K/524288K available (11264K kernel code, 679K rwdata, 6016K rodata, 4096K init, 511K bss, 29704K reserved, 327680K cma-reserved, 0K highmem) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xa0800000 - 0xff800000 (1520 MB) lowmem : 0x80000000 - 0xa0000000 ( 512 MB) pkmap : 0x7fe00000 - 0x80000000 ( 2 MB) modules : 0x7f000000 - 0x7fe00000 ( 14 MB) .text : 0x80008000 - 0x80c00000 (12256 kB) .init : 0x81300000 - 0x81700000 (4096 kB) .data : 0x81700000 - 0x817a9f60 ( 680 kB) .bss : 0x817ab000 - 0x8182acac ( 512 kB) SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Preemptible hierarchical RCU implementation. Build-time adjustment of leaf fanout to 32. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2 NR_IRQS:16 nr_irqs:16 16 arm_arch_timer: Architected cp15 timer(s) running at 8.00MHz (phys). clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns Switching to timer-based delay loop, resolution 125ns Ignoring duplicate/late registration of read_current_timer delay clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns Console: colour dummy device 80x30 Calibrating delay loop (skipped), value calculated using timer frequency.. 16.00 BogoMIPS (lpj=80000) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok CPU0: update cpu_capacity 1024 CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x80100000 - 0x80100058 CPU1: update cpu_capacity 1024 CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated (32.00 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 512 (order: 3, 32768 bytes) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations cpuidle: using governor ladder cpuidle: using governor menu DDR type is DDR3! hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. hw-breakpoint: maximum watchpoint size is 8 bytes. imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver imx7d-pinctrl 30330000.iomuxc: initialized IMX pinctrl driver MU is ready for cross core communication! GPIO line 13 (MCU_INTB) hogged as input GPIO line 60 (LAN1_INT_N) hogged as input GPIO line 62 (LAN1_COMA_MODE) hogged as output/low mxs-dma 33000000.dma-apbh: initialized vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb 30800000.aips-bus:usbphynop1 supply vcc not found, using dummy regulator 30800000.aips-bus:usbphynop2 supply vcc not found, using dummy regulator i2c i2c-0: IMX I2C adapter registered i2c i2c-0: can't use DMA, using PIO instead. i2c i2c-2: IMX I2C adapter registered i2c i2c-2: can't use DMA, using PIO instead. gpio_bmic 3-0014: version: 2.0 bmic_regulator 3-0016: version: 1.0 i2c i2c-3: IMX I2C adapter registered i2c i2c-3: can't use DMA, using PIO instead. Linux video capture interface: v2.00 pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered MIPI CSI2 driver module loaded imx rpmsg driver is registered. Advanced Linux Sound Architecture Driver Initialized. Bluetooth: Core ver 2.22 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized random: fast init done armadillo_iotg_addon addon: Atmark Techno SD board detected at Add-On Module I/F 1(Rev 1, SerialNumber=3630). armadillo_iotg_addon addon: No add-on expansion board detected at Add-On Module I/F 2. clocksource: Switched to clocksource arch_sys_counter VFS: Disk quotas dquot_6.6.0 VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 2, 16384 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Bus freq driver module loaded workingset: timestamp_bits=14 max_order=17 bucket_order=3 squashfs: version 4.0 (2009/01/31) Phillip Lougher NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.26) NET: Registered protocol family 38 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) OF: PCI: host bridge /soc/pcie@0x33800000 ranges: OF: PCI: No bus range found for /soc/pcie@0x33800000, using [bus 00-ff] OF: PCI: IO 0x4ff80000..0x4ff8ffff -> 0x00000000 OF: PCI: MEM 0x40000000..0x4fefffff -> 0x40000000 imx6q-pcie 33800000.pcie: Speed change timeout imx6q-pcie 33800000.pcie: Roll back to GEN1 link! imx6q-pcie 33800000.pcie: Link up, Gen1 imx6q-pcie 33800000.pcie: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fefffff] PCI: bus0: Fast back to back transfers disabled PCI: bus1: Fast back to back transfers disabled pci 0000:00:00.0: BAR 14: assigned [mem 0x40000000-0x405fffff] pci 0000:00:00.0: BAR 0: assigned [mem 0x40600000-0x406fffff] pci 0000:00:00.0: BAR 6: assigned [mem 0x40700000-0x4070ffff pref] pci 0000:01:00.0: BAR 2: assigned [mem 0x40000000-0x403fffff 64bit] pci 0000:01:00.0: BAR 0: assigned [mem 0x40400000-0x4040ffff 64bit] pci 0000:00:00.0: PCI bridge to [bus 01-ff] pci 0000:00:00.0: bridge window [mem 0x40000000-0x405fffff] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt pci 0000:01:00.0: Signaling PME through PCIe PME interrupt imx-sdma 30bd0000.sdma: loaded firmware 4.2 pfuze100-regulator 3-0009: Full layer: 1, Metal layer: 1 pfuze100-regulator 3-0009: FAB: 0, FIN: 0 pfuze100-regulator 3-0009: pfuze3000 found. 30860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 44, base_baud = 5000000) is a IMX 30a70000.serial: ttymxc4 at MMIO 0x30a70000 (irq = 48, base_baud = 5000000) is a IMX console [ttymxc4] enabled imx sema4 driver is registered. [drm] Initialized [drm] Initialized vivante 1.0.0 20120216 on minor 0 brd: module loaded loop: module loaded (hci_tty): inside hci_tty_init (hci_tty): allocated 246, 0 fsl-quadspi 30bb0000.qspi: n25q128a13 (16384 Kbytes) 3 ofpart partitions found on MTD device 30bb0000.qspi Creating 3 MTD partitions on "30bb0000.qspi": 0x000000000000-0x000000100000 : "bootloader" 0x000000100000-0x000000140000 : "license" 0x000000140000-0x000004000000 : "reserved" mtd: partition "reserved" extends beyond the end of device "30bb0000.qspi" -- size truncated to 0xec0000 libphy: Fixed MDIO Bus: probed tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky CAN device driver interface 30bf0000.ethernet supply phy not found, using dummy regulator pps pps0: new PPS source ptp0 libphy: fec_enet_mii_bus: probed fec 30bf0000.ethernet eth0: registered PHC device 0 PPP generic driver version 2.4.2 usbcore: registered new interface driver kaweth pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver usbcore: registered new interface driver pegasus usbcore: registered new interface driver rtl8150 usbcore: registered new interface driver r8152 usbcore: registered new interface driver asix usbcore: registered new interface driver ax88179_178a usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver cdc_eem usbcore: registered new interface driver smsc95xx usbcore: registered new interface driver net1080 usbcore: registered new interface driver cdc_subset usbcore: registered new interface driver zaurus usbcore: registered new interface driver sierra_net usbcore: registered new interface driver cdc_ncm usbcore: registered new interface driver qmi_wwan ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-mxc: Freescale On-Chip EHCI Host driver usbcore: registered new interface driver cdc_acm cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters usbcore: registered new interface driver cdc_wdm usbcore: registered new interface driver usb-storage usbcore: registered new interface driver usbserial usbcore: registered new interface driver usbserial_generic usbserial: USB Serial support registered for generic usbcore: registered new interface driver cp210x usbserial: USB Serial support registered for cp210x usbcore: registered new interface driver ftdi_sio usbserial: USB Serial support registered for FTDI USB Serial Device usbcore: registered new interface driver option usbserial: USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver sierra usbserial: USB Serial support registered for Sierra USB modem usbcore: registered new interface driver usb_serial_simple usbserial: USB Serial support registered for carelink usbserial: USB Serial support registered for zio usbserial: USB Serial support registered for funsoft usbserial: USB Serial support registered for flashloader usbserial: USB Serial support registered for google usbserial: USB Serial support registered for libtransistor usbserial: USB Serial support registered for vivopay usbserial: USB Serial support registered for moto_modem usbserial: USB Serial support registered for motorola_tetra usbserial: USB Serial support registered for novatel_gps usbserial: USB Serial support registered for hp4x usbserial: USB Serial support registered for suunto usbserial: USB Serial support registered for siemens_mpi usbcore: registered new interface driver usb_ehset_test usb3503 3-0008: switched to HUB mode usb3503 3-0008: usb3503_probe: probed in hub mode 30b10200.usbmisc supply vbus-wakeup not found, using dummy regulator 30b30200.usbmisc supply vbus-wakeup not found, using dummy regulator 30b20200.usbmisc supply vbus-wakeup not found, using dummy regulator ci_hdrc ci_hdrc.0: EHCI Host Controller ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected 30b30000.usb supply vbus not found, using dummy regulator ci_hdrc ci_hdrc.1: EHCI Host Controller ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2 ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected udc-core: couldn't find an available UDC - added [g_cdc] to list of pending drivers mousedev: PS/2 mouse device common for all mice input: 30370000.snvs:snvs-powerkey as /devices/soc0/soc/30000000.aips-bus/30370000.snvs/30370000.snvs:snvs-powerkey/input/input0 bmic_rtc 3-0011: version: 1.1 bmic_rtc 3-0011: rtc core: registered bmic_rtc as rtc0 snvs_rtc 30370000.snvs:snvs-rtc-lp: rtc core: registered 30370000.snvs:snvs- as rtc1 i2c /dev entries driver IR NEC protocol handler initialized IR RC5(x/sz) protocol handler initialized IR RC6 protocol handler initialized IR JVC protocol handler initialized IR Sony protocol handler initialized IR SANYO protocol handler initialized IR Sharp protocol handler initialized IR MCE Keyboard/mouse protocol handler initialized IR XMP protocol handler initialized Unable to handle kernel NULL pointer dereference at virtual address 00000000 pgd = 80004000 [00000000] *pgd=00000000 Internal error: Oops: 5 [#1] PREEMPT SMP ARM Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.9.133-at30 #6 Hardware name: Freescale i.MX7 Dual (Device Tree) task: 88070000 task.stack: 8806c000 PC is at v4l2_async_notifier_register+0x3c/0x168 LR is at mx6s_csi_probe+0x35c/0x500 pc : [<807b6a68>] lr : [<807e02b4>] psr: 80080013 sp : 8806de28 ip : 88ae52e0 fp : 00000007 r10: 00000000 r9 : 88ae502c r8 : 8bac7be0 r7 : 88ae501c r6 : 88ae51fc r5 : 00000000 r4 : 88ae52d4 r3 : 00000000 r2 : 88ae5304 r1 : 88ae52d4 r0 : 88ae501c Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none Control: 10c53c7d Table: 88ac006a DAC: 00000051 Process swapper/0 (pid: 1, stack limit = 0x8806c218) Stack: (0x8806de28 to 0x8806e000) de20: 88ae5010 00000000 88ae51fc 88ae501c 8bac7be0 807e02b4 de40: 00000000 810d0fe8 88ae5010 00000000 88172aa0 81179244 00000001 88176610 de60: 88176610 fffffffe 8176b2bc fffffdfb 00000000 817ab000 000001e4 80528da4 de80: 81807bc0 88176610 8176b2bc 00000000 00000000 80527614 88176610 8176b2bc dea0: 88176644 00000000 8136a834 805277b0 00000000 8176b2bc 80527700 80525a60 dec0: 8806755c 88167db4 8176b2bc 88ae9f80 81741588 80526bac 81148134 8134b2d4 dee0: 00000000 8176b2bc 8134b2d4 00000000 8136a854 80527e88 ffffe000 8134b2d4 df00: 00000000 80101778 00000000 80288b10 817fc0e8 8813a680 00000000 81717d5c df20: 8bfffb36 000001e4 80c3012c 8014ce8c 811dd3e8 81132ab0 00000006 00000006 df40: 8109521c 00000000 81717d44 00000006 817ab000 813004c8 81388df0 817ab000 df60: 813004c8 8136a854 8136a834 81300e38 00000006 00000006 00000000 813004c8 df80: 80bf0c2c 00000000 80bf0c2c 00000000 00000000 00000000 00000000 00000000 dfa0: 00000000 80bf0c34 00000000 80107990 00000000 00000000 00000000 00000000 dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000 [<807b6a68>] (v4l2_async_notifier_register) from [<807e02b4>] (mx6s_csi_probe+0x35c/0x500) [<807e02b4>] (mx6s_csi_probe) from [<80528da4>] (platform_drv_probe+0x50/0xac) [<80528da4>] (platform_drv_probe) from [<80527614>] (driver_probe_device+0x1bc/0x2a8) [<80527614>] (driver_probe_device) from [<805277b0>] (__driver_attach+0xb0/0xb4) [<805277b0>] (__driver_attach) from [<80525a60>] (bus_for_each_dev+0x78/0x9c) [<80525a60>] (bus_for_each_dev) from [<80526bac>] (bus_add_driver+0x1bc/0x200) [<80526bac>] (bus_add_driver) from [<80527e88>] (driver_register+0x78/0xf4) [<80527e88>] (driver_register) from [<80101778>] (do_one_initcall+0x44/0x180) [<80101778>] (do_one_initcall) from [<81300e38>] (kernel_init_freeable+0x1c8/0x254) [<81300e38>] (kernel_init_freeable) from [<80bf0c34>] (kernel_init+0x8/0x10c) [<80bf0c34>] (kernel_init) from [<80107990>] (ret_from_fork+0x14/0x24) Code: e581c010 e5813014 e5813018 e5923000 (e5932000) ---[ end trace cff435c64d9999a7 ]--- Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b CPU1: stopping CPU: 1 PID: 0 Comm: swapper/1 Tainted: G D 4.9.133-at30 #6 Hardware name: Freescale i.MX7 Dual (Device Tree) [<8010f7fc>] (unwind_backtrace) from [<8010b470>] (show_stack+0x10/0x14) [<8010b470>] (show_stack) from [<803fffb8>] (dump_stack+0x78/0x8c) [<803fffb8>] (dump_stack) from [<8010e618>] (handle_IPI+0x180/0x1ac) [<8010e618>] (handle_IPI) from [<80101504>] (gic_handle_irq+0x88/0x8c) [<80101504>] (gic_handle_irq) from [<8010bd8c>] (__irq_svc+0x6c/0xa8) Exception stack(0x8809df80 to 0x8809dfc8) df80: 00000001 00000000 00000000 80118760 00000000 00000000 ffffe000 817a9c36 dfa0: 81704d88 81620ea8 81704d80 8109603c 00000000 8809dfd0 801083d0 801083d4 dfc0: 60000013 ffffffff [<8010bd8c>] (__irq_svc) from [<801083d4>] (arch_cpu_idle+0x38/0x3c) [<801083d4>] (arch_cpu_idle) from [<8016fef8>] (cpu_startup_entry+0x1b8/0x224) [<8016fef8>] (cpu_startup_entry) from [<801015ac>] (__enable_mmu+0x0/0x14) ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b usb 2-1: new high-speed USB device number 2 using ci_hdrc hub 2-1:1.0: USB hub found hub 2-1:1.0: 3 ports detected usb 2-1.1: new full-speed USB device number 3 using ci_hdrc cp210x 2-1.1:1.0: cp210x converter detected usb 2-1.1: cp210x converter now attached to ttyUSB0 U-Boot SPL 2016.07-at23 (Nov 01 2023 - 14:36:48) Trying to boot from MMC1 U-Boot 2016.07-at23 (Nov 01 2023 - 14:36:48 +0900) CPU: Freescale i.MX7D rev1.3 at 996MHz CPU: Extended Commercial temperature grade (-20C to 105C) at 44C Reset cause: POR Watchdog enabled I2C: ready DRAM: 512 MiB Boot Source: SD Board Type: Armadillo-X1(0a100000) Revision: 0002 S/N: 49746 DRAM: 00001d05 XTAL: 00 X1 Addon EEPROM Detect Atmark Techno Ext SD Slot Detect MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... *** Warning - bad CRC, using default environment Failed (-5) Loading Environment from MMC... *** Warning - bad CRC, using default environment Failed (-5) In: serial Out: serial Err: serial Found PFUZE300! deviceid 0x30, revid 0x11 Net: FEC0 =>