U-Boot 2020.04-at25 (Feb 25 2025 - 01:54:53 +0000)
CPU: i.MX6ULL rev1.0 at 396 MHz
Model: Atmark Techno Armadillo-600 Series
DRAM: 512 MiB
setup_rtc_disarm_alarm: Can't find bus
WDT: Started with servicing (10s timeout)
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: mxc_serial
Out: mxc_serial
Err: mxc_serial
switch to partitions #0, OK
mmc0(part 0) is current device
Net: eth0: ethernet@2188000
Fastboot: Normal
Normal Boot
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0(part 0) is current device
6473368 bytes read in 888 ms (7 MiB/s)
Booting from mmc ...
38953 bytes read in 26 ms (1.4 MiB/s)
Loading fdt boot/armadillo-640.dtb
45 bytes read in 14 ms (2.9 KiB/s)
4413 bytes read in 18 ms (239.3 KiB/s)
Applying fdt overlay: armadillo-640-lcd70ext-l00.dtbo
## Booting kernel from Legacy Image at 80800000 ...
Image Name: Linux-5.10.234-0-at
Created: 2025-02-21 3:55:01 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 6473304 Bytes = 6.2 MiB
Load Address: 82000000
Entry Point: 82000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 83500000
Booting using the fdt blob at 0x83500000
Loading Kernel Image
Loading Device Tree to 9ef1c000, end 9ef48fff ... OK
Starting kernel ...
OpenRC 0.55.1 is starting up Linux 5.10.234-0-at (armv7l)
* Mounting /proc ... [ ok ]
* Mounting /run ... [ ok ]
* /run/openrc: creating directory
* /run/lock: creating directory
* /run/lock: correcting owner
* Caching service dependencies ... [ ok ]
* Clock skew detected with `/etc/init.d'
* Adjusting mtime of `/run/openrc/deptree' to Wed Mar 5 11:44:03 2025
* WARNING: clock skew detected!
* Mounting /sys ... * Remounting devtmpfs on /dev ... [ ok ]
[ ok ]
* Mounting security filesystem ... [ ok ]
* Mounting config filesystem ... [ ok ]
* Mounting /dev/mqueue ... [ ok ]
* Mounting /dev/pts ... [ ok ]
* Mounting /dev/shm ... [ ok ]
udev | * Starting udev ... [ ok ]
fsck_atlog | * Checking log filesystems ... * Clearing dirty bit of /dev/mmcblk0gp1. This is sign of unclean shutdown
fsck | * Checking local filesystems ... [ ok ]
fsck_atlog | * /dev/mmcblk0p3 was not unmounted properly, running fsck
root | * Remounting filesystems ... [ ok ]
fsck_atlog | [ ok ]
localmount | * Mounting local filesystems ... [ ok ]
overlayfs | * Preparing overlayfs over / ... [ ok ]
* WARNING: clock skew detected!
sysctl | * Configuring kernel parameters ...hostname | * Setting hostname ...udev-trigger | * Generating a rule to create a /dev/root symlink ... [ ok ]
[ ok ]
[ ok ]
udev-trigger | * Populating /dev with existing devices through uevents ... [ ok ]
bootmisc | * Creating user login records ... [ ok ]
bootmisc | * Wiping /var/tmp directory ... [ ok ]
syslog | * Starting busybox syslog ...dbus | * /run/dbus: creating directory
dbus | * /run/dbus: correcting owner
micron-emmc-reten | * Starting micron-emmc-reten
dbus | * Starting System Message Bus ... [ ok ]
[ ok ]
micron-emmc-reten | [ ok ]
klogd | * Starting busybox klogd ... [ ok ]
networkmanager | * Starting networkmanager ... [ ok ]
dnsmasq | * /var/lib/misc/dnsmasq.leases: creating file
dnsmasq | * /var/lib/misc/dnsmasq.leases: correcting owner
dnsmasq | * Starting dnsmasq ... [ ok ]
* WARNING: clock skew detected!
buttond | * Starting button watching daemon ...reset_bootcount | * Resetting bootcount in bootloader env ... [ ok ]
Environment OK, copy 1
reset_bootcount | [ ok ]
podman-atmark | * Starting configured podman containers ...zramswap | * Creating zram swap device ...avahi-daemon | * Starting avahi-daemon ... [ ok ]
chronyd | * Starting chronyd ... [ ok ]
[ ok ]
abos-web | * Starting abos-web ... [ ok ]
[ ok ]
local | * Starting local ... [ ok ]
Welcome to Alpine Linux 3.21
Kernel 5.10.234-0-at on an armv7l (/dev/ttymxc0)
armadillo login: root
You are required to change your password immediately (administrator enforced).
New password:
Retype new password:
Welcome to Alpine!
The Alpine Wiki contains a large amount of how-to guides and general
information about administrating Alpine systems.
See .
Please note this system is READ-ONLY with a read-write overlayfs,
after updating password make sure to save new password with
# persist_file /etc/shadow
You can change this message by editing /etc/motd.
WARNING: swupdate onetime public certificate is present, anyone can access this device
WARNING: Please install initial_setup.swu (from mkswu --init),
WARNING: or remove it with 'abos-ctrl certificates remove-onetime'
armadillo:~#
armadillo:~#
armadillo:~#
armadillo:~#
armadillo:~#
armadillo:~#
armadillo:~# ls
armadillo:~#
armadillo:~# pwd
/root
armadillo:~#
armadillo:~#
armadillo:~# ls
armadillo:~#
armadillo:~#
armadillo:~#
armadillo:~#
armadillo:~#
armadillo:~#
armadillo:~#
U-Boot 2018.03-at8 installer+ (Feb 17 2020 - 19:19:21 +0900)
CPU: Freescale i.MX6ULL rev1.0 at 396 MHz
Reset cause: POR
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
Net: FEC
Hit any key to stop autoboot: 0
6601520 bytes read in 442 ms (14.2 MiB/s)
28077 bytes read in 52 ms (526.4 KiB/s)
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-4.14-at19
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 6601456 Bytes = 6.3 MiB
Load Address: 82000000
Entry Point: 82000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 83000000
Booting using the fdt blob at 0x83000000
Loading Kernel Image ... OK
Loading Device Tree to 9eef9000, end 9ef02dac ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.14-at19 (atmark@atde7) (gcc version 6.3.0 20170516 (Debian 6.3.0-18)) #1 Wed Feb 19 11:40:11 JST 2020
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Atmark Techno Armadillo-640
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] cma: Reserved 16 MiB at 0x9f000000
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920
[ 0.000000] Kernel command line: root=/dev/mmcblk1p2 rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 490912K/524288K available (6144K kernel code, 259K rwdata, 1288K rodata, 3072K init, 242K bss, 16992K reserved, 16384K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0700000 (7136 kB)
[ 0.000000] .init : 0xc0900000 - 0xc0c00000 (3072 kB)
[ 0.000000] .data : 0xc0c00000 - 0xc0c40d00 ( 260 kB)
[ 0.000000] .bss : 0xc0c45d64 - 0xc0c82734 ( 243 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] Switching to timer-based delay loop, resolution 41ns
[ 0.000017] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[ 0.000056] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.001774] Console: colour dummy device 80x30
[ 0.002363] console [tty0] enabled
[ 0.002429] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.002489] pid_max: default: 32768 minimum: 301
[ 0.002909] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.002960] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.004162] CPU: Testing write buffer coherency: ok
[ 0.005229] Setting up static identity map for 0x80100000 - 0x80100060
[ 0.007244] devtmpfs: initialized
[ 0.017284] random: get_random_u32 called from bucket_table_alloc+0x84/0x1bc with crng_init=0
[ 0.017787] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.018207] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.018280] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.019632] pinctrl core: initialized pinctrl subsystem
[ 0.020968] NET: Registered protocol family 16
[ 0.022843] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.031342] vdd3p0: supplied by regulator-dummy
[ 0.032146] cpu: supplied by regulator-dummy
[ 0.032927] vddsoc: supplied by regulator-dummy
[ 0.047124] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
[ 0.047729] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver
[ 0.075949] SCSI subsystem initialized
[ 0.076289] usbcore: registered new interface driver usbfs
[ 0.076390] usbcore: registered new interface driver hub
[ 0.076533] usbcore: registered new device driver usb
[ 0.077974] i2c-gpio i2c-gpio: using pins 117 (SDA) and 120 (SCL)
[ 0.078983] Advanced Linux Sound Architecture Driver Initialized.
[ 0.081211] clocksource: Switched to clocksource mxc_timer1
[ 0.096845] NET: Registered protocol family 2
[ 0.098041] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.098191] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.098316] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.098508] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.098577] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.098914] NET: Registered protocol family 1
[ 0.099615] RPC: Registered named UNIX socket transport module.
[ 0.099673] RPC: Registered udp transport module.
[ 0.099702] RPC: Registered tcp transport module.
[ 0.099731] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.411658] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.427539] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.429479] NFS: Registering the id_resolver key type
[ 0.429581] Key type id_resolver registered
[ 0.429616] Key type id_legacy registered
[ 0.429719] fuse init (API version 7.26)
[ 0.438065] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 0.438138] io scheduler noop registered
[ 0.438169] io scheduler deadline registered
[ 0.438623] io scheduler cfq registered (default)
[ 0.444191] mxsfb 21c8000.lcdif: 21c8000.lcdif supply lcd not found, using dummy regulator
[ 0.449286] mxsfb 21c8000.lcdif: failed to find mxc display driver
[ 0.482400] Console: switching to colour frame buffer device 100x30
[ 0.504938] mxsfb 21c8000.lcdif: initialized
[ 0.520243] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 18, base_baud = 5000000) is a IMX
[ 0.527267] Console IMX rounded baud rate from 114943 to 114900
[ 0.538916] imx-sdma 20ec000.sdma: loaded firmware 3.3
[ 1.045235] console [ttymxc0] enabled
[ 1.057460] 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 52, base_baud = 5000000) is a IMX
[ 1.074421] 21f4000.serial: ttymxc4 at MMIO 0x21f4000 (irq = 53, base_baud = 5000000) is a IMX
[ 1.092500] libphy: Fixed MDIO Bus: probed
[ 1.104004] tun: Universal TUN/TAP device driver, 1.6
[ 1.116682] CAN device driver interface
[ 1.129512] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator
[ 1.147184] libphy: fec_enet_mii_bus: probed
[ 1.194817] usbcore: registered new interface driver awl13
[ 1.207846] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[ 1.223019] usbcore: registered new interface driver pegasus
[ 1.236582] usbcore: registered new interface driver rtl8150
[ 1.250056] usbcore: registered new interface driver r8152
[ 1.263052] usbcore: registered new interface driver lan78xx
[ 1.275903] usbcore: registered new interface driver asix
[ 1.288350] usbcore: registered new interface driver ax88179_178a
[ 1.301511] usbcore: registered new interface driver cdc_ether
[ 1.314364] usbcore: registered new interface driver net1080
[ 1.326765] usbcore: registered new interface driver cdc_subset
[ 1.339136] usbcore: registered new interface driver zaurus
[ 1.350916] usbcore: registered new interface driver cdc_ncm
[ 1.362468] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.374925] ehci-mxc: Freescale On-Chip EHCI Host driver
[ 1.386190] usbcore: registered new interface driver cdc_acm
[ 1.397481] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.411447] usbcore: registered new interface driver usb-storage
[ 1.423373] usbcore: registered new interface driver usbserial
[ 1.435030] usbcore: registered new interface driver usbserial_generic
[ 1.447070] usbserial: USB Serial support registered for generic
[ 1.458607] usbcore: registered new interface driver cp210x
[ 1.469719] usbserial: USB Serial support registered for cp210x
[ 1.481056] usbcore: registered new interface driver ftdi_sio
[ 1.492057] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 1.504770] usbcore: registered new interface driver mxuport
[ 1.515711] usbserial: USB Serial support registered for MOXA UPort
[ 1.527236] usbcore: registered new interface driver pl2303
[ 1.538227] usbserial: USB Serial support registered for pl2303
[ 1.555780] ci_hdrc ci_hdrc.0: EHCI Host Controller
[ 1.566568] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
[ 1.601250] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
[ 1.614307] hub 1-0:1.0: USB hub found
[ 1.624414] hub 1-0:1.0: 1 port detected
[ 1.639831] ci_hdrc ci_hdrc.1: EHCI Host Controller
[ 1.651295] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2
[ 1.691253] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[ 1.704959] hub 2-0:1.0: USB hub found
[ 1.715496] hub 2-0:1.0: 1 port detected
[ 1.727781] udc-core: couldn't find an available UDC - added [g_cdc] to list of pending drivers
[ 1.745298] snvs_rtc 20cc000.snvs:snvs-rtc-lp: registered as rtc0
[ 1.758549] i2c /dev entries driver
[ 1.769005] IR NEC protocol handler initialized
[ 1.780286] IR RC5(x/sz) protocol handler initialized
[ 1.792202] IR RC6 protocol handler initialized
[ 1.803465] IR JVC protocol handler initialized
[ 1.814509] IR Sony protocol handler initialized
[ 1.825575] IR SANYO protocol handler initialized
[ 1.836681] IR Sharp protocol handler initialized
[ 1.847510] IR MCE Keyboard/mouse protocol handler initialized
[ 1.859452] IR XMP protocol handler initialized
[ 1.871949] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
[ 1.884558] sdhci: Secure Digital Host Controller Interface driver
[ 1.896958] sdhci: Copyright(c) Pierre Ossman
[ 1.907325] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.981250] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
[ 2.061615] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
[ 2.076962] usbcore: registered new interface driver usbhid
[ 2.088928] usbhid: USB HID core driver
[ 2.109674] mmc0: new DDR MMC card at address 0001
[ 2.120748] random: fast init done
[ 2.135627] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.148683] NET: Registered protocol family 10
[ 2.161361] mmcblk0: mmc0:0001 Q2J55L 3.53 GiB
[ 2.172685] mmcblk0boot0: mmc0:0001 Q2J55L partition 1 2.00 MiB
[ 2.186251] Segment Routing with IPv6
[ 2.196012] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.209199] NET: Registered protocol family 17
[ 2.219801] can: controller area network core (rev 20170425 abi 9)
[ 2.232596] NET: Registered protocol family 29
[ 2.243392] can: raw protocol (rev 20170425)
[ 2.253958] can: broadcast manager protocol (rev 20170425 t)
[ 2.266041] can: netlink gateway (rev 20170425) max_hops=1
[ 2.278507] Key type dns_resolver registered
[ 2.290128] cpu cpu0: _opp_add: duplicate OPPs detected. Existing: freq: 900000000, volt: 1275000, enabled: 1. New: freq: 900000000, volt: 1275000, enabled: 1
[ 2.318262] cpu cpu0: _opp_add: duplicate OPPs detected. Existing: freq: 792000000, volt: 1225000, enabled: 1. New: freq: 792000000, volt: 1225000, enabled: 1
[ 2.347049] cpu cpu0: _opp_add: duplicate OPPs detected. Existing: freq: 528000000, volt: 1175000, enabled: 1. New: freq: 528000000, volt: 1175000, enabled: 1
[ 2.376583] cpu cpu0: _opp_add: duplicate OPPs detected. Existing: freq: 396000000, volt: 1025000, enabled: 1. New: freq: 396000000, volt: 1025000, enabled: 1
[ 2.407129] cpu cpu0: _opp_add: duplicate OPPs detected. Existing: freq: 198000000, volt: 950000, enabled: 1. New: freq: 198000000, volt: 950000, enabled: 1
[ 2.439203] ThumbEE CPU extension supported.
[ 2.450512] mmcblk0boot1: mmc0:0001 Q2J55L partition 2 2.00 MiB
[ 2.463582] mmcblk0gp0: mmc0:0001 Q2J55L partition 4 8.00 MiB
[ 2.476422] mmcblk0gp1: mmc0:0001 Q2J55L partition 5 8.00 MiB
[ 2.491186] mmcblk0gp2: mmc0:0001 Q2J55L partition 6 8.00 MiB
[ 2.506714] mmcblk0gp3: mmc0:0001 Q2J55L partition 7 8.00 MiB
[ 2.519153] mmcblk0rpmb: mmc0:0001 Q2J55L partition 3 4.00 MiB, chardev (248:0)
[ 2.538471] input: gpio-keys as /devices/soc0/gpio-keys/input/input0
[ 2.551769] mmcblk0: p1
[ 2.563509] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01 00:00:00 UTC (0)
[ 2.586042] 5V: disabling
[ 2.595124] ALSA device list:
[ 2.604397] No soundcards found.
[ 2.616432] Warning: unable to open an initial console.
[ 2.633507] Freeing unused kernel memory: 3072K
[ 2.647038] mmcblk0gp1:
[ 2.657716] mmc1: host does not support reading read-only switch, assuming write-enable
[ 2.693298] mmc1: new high speed SDHC card at address b368
[ 2.713226] mmcblk1: mmc1:b368 USD 7.51 GiB
[ 2.735202] mmcblk1: p1 p2
[ 2.832552] systemd-udevd[75]: starting version 215
[ 2.853977] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 4.190319] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null)
Mounting proc: failed
Remounting root rw: [ 4.638041] EXT4-fs (mmcblk1p2): re-mounted. Opts: data=ordered
done
Mounting sysfs: failed
Mounting devtmpfs on /dev: failed
Cleaning up system: done
Running local start scripts.
Creating mtd devnode: done
Starting udevd: done
Mounting devpts: done
Changing file permissions: done
Configure /home/ftp: done
Starting syslogd: done
Starting klogd: done
Mounting tmpfs on /tmp, /var/tmp: done
Mounting ramfs on /home/ftp/pub: done
Configuring network interfaces: [ 7.271440] SMSC LAN8710/LAN8720 2188000.ethernet-1:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=2188000.ethernet-1:00, irq=POLL)
[ 7.363029] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
udhcpc (v1.20.2) started
Sending discover...
Sending discover...
Sending discover...
init eth0
No lease, failing
failed
Setting hostname: done
Starting inetd: done
Running local start script (/etc/config/rc.local).
*+*+* Install Start!! *+*+*
=== Step.1 Formatting eMMC ===
Command (m for help): Building a new DOS disklabel. Changes will remain in memory only,
until you decide to write them. After that the previous content
won't be recoverable.
Command (m for help): Command action
e extended
p primary partition (1-4)
Partition number (1-4): First cylinder (1-459, default 1): Using default value 1
Last cylinder or +size or +sizeM or +sizeK (1-459, default 459):
Command (m for help): Command action
e extended
p primary partition (1-4)
Partition number (1-4): First cylinder (2-459, default 2): Using default value 2
Last cylinder or +size or +sizeM or +sizeK (2-459, default 459):
Command (m for help): Command action
e extended
p primary partition (1-4)
Partition number (1-4): First cylinder (7-459, default 7): Using default value 7
Last cylinder or +size or +sizeM or +sizeK (7-459, default 459):
Command (m for help): Command action
e extended
p primary partition (1-4)
Selected partition 2
First cylinder (24-459, default 24): Using default value 24
Last cylinder or +size or +sizeM or +sizeK (24-459, default 459): Using default value 459
Command (m for help): Partition number (1-4): Hex code (type L to list codes): Changed system type of partition 1 to b (Win95 FAT32)
Command (m for help): Partition number (1-4): Hex code (type L to list codes):
Command (m for help): Partition number (1-4): Hex code (type L to list codes): Changed system type of partition 3 to b (Win95 FAT32)
Command (m for help): Partition number (1-4):
Command (m for help):
Disk /dev/mmcblk0: 3791 MB, 3791650816 bytes
256 heads, 63 sectors/track, 459 cylinders
Units = cylinders of 16128 * 512 = 8257536 bytes
Device Boot Start End Blocks Id System
/dev/mmcblk0p1 2 6 40320 b Win95 FAT32
/dev/mmcblk0p2 24 459 3515904 83 Linux
/dev/mmcblk0p3 7 23 137088 b Win95 FAT32
Partition table entries are not in disk order
Command (m for help): [ 19.923232] mmcblk0: p1 p2 p3
The partition table has been altered.
Calling ioctl() to re-read partition table
mkfs.vfat 2.11 (12 Mar 2005)
mke2fs 1.42.5 (29-Jul-2012)
[ 20.110104] random: crng init done
Discarding device blocks: 4096/878976528384/878976 done
Filesystem label=
OS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)
Stride=0 blocks, Stripe width=0 blocks
219888 inodes, 878976 blocks
43948 blocks (5.00%) reserved for the super user
First data block=0
Maximum filesystem blocks=901775360
27 block groups
32768 blocks per group, 32768 fragments per group
8144 inodes per group
Superblock backups stored on blocks:
32768, 98304, 163840, 229376, 294912, 819200
Allocating group tables: 0/27 1/27 2/27 3/27 4/27 5/27 6/27 7/27 8/27 9/2710/2711/2712/2713/2714/2715/2716/2717/2718/2719/2720/2721/2722/2723/2724/2725/2726/27 done
Writing inode tables: 0/27 1/27 2/27 3/27 4/27 5/27 6/27 7/27 8/27 9/2710/2711/2712/2713/2714/2715/2716/2717/2718/2719/2720/2721/2722/2723/2724/2725/2726/27 done
Creating journal (16384 blocks): done
Writing superblocks and filesystem accounting information: 0/27 1/27 2/27 3/27 4/27 5/27 6/27 7/27 8/27 9/2710/2711/2712/2713/2714/2715/2716/2717/2718/2719/2720/2721/2722/2723/2724/2725/2726/27 done
mkfs.vfat 2.11 (12 Mar 2005)
Disk /dev/mmcblk0: 3791 MB, 3791650816 bytes
256 heads, 63 sectors/track, 459 cylinders
Units = cylinders of 16128 * 512 = 8257536 bytes
Device Boot Start End Blocks Id System
/dev/mmcblk0p1 2 6 40320 b Win95 FAT32
/dev/mmcblk0p2 24 459 3515904 83 Linux
/dev/mmcblk0p3 7 23 137088 b Win95 FAT32
Partition table entries are not in disk order
=== Step.2 Setup Partition ===
/images/debian-buster-armhf-a600-20210224.tar.gz: OK
[ 43.309568] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
/images/uImage: OK
[ 148.130558] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
uImage
/images/a640.dtb: OK
[ 148.610446] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
a640.dtb
uImage
=== Step.3 Setup Bootloader ===
/images/u-boot.imx: OK
295+0 records in
295+0 records out
302080 bytes (295.0KB) copied, 0.038563 seconds, 7.5MB/s
512+0 records in
512+0 records out
524288 bytes (512.0KB) copied, 0.067462 seconds, 7.4MB/s
512+0 records in
512+0 records out
524288 bytes (512.0KB) copied, 0.106015 seconds, 4.7MB/s
=== Step.4 sync ===
Write Protect Groups 0-0 (Blocks 0-16383), Temporary Write Protection
*+*+* Install Completed!! *+*+*
U-Boot 2018.03-at13 (Mar 29 2022 - 11:11:47 +0900)
CPU: Freescale i.MX6ULL rev1.0 at 396 MHz
Reset cause: POR
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment
Failed (-5)
In: serial
Out: serial
Err: serial
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
Net: FEC
Hit any key to stop autoboot: 0
7639192 bytes read in 219 ms (33.3 MiB/s)
29280 bytes read in 54 ms (529.3 KiB/s)
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-4.14-at62
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 7639128 Bytes = 7.3 MiB
Load Address: 82000000
Entry Point: 82000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 83000000
Booting using the fdt blob at 0x83000000
Loading Kernel Image ... OK
Loading Device Tree to 9eef9000, end 9ef0325f ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.14-at62 (atmark@atde8) (gcc version 8.3.0 (Debian 8.3.0-2)) #3 Fri Oct 27 18:56:23 JST 2023
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Atmark Techno Armadillo-640
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] cma: Reserved 16 MiB at 0x9f000000
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920
[ 0.000000] Kernel command line: root=/dev/mmcblk0p2 rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 490884K/524288K available (6144K kernel code, 275K rwdata, 1420K rodata, 3072K init, 244K bss, 17020K reserved, 16384K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0700000 (7136 kB)
[ 0.000000] .init : 0xc0900000 - 0xc0c00000 (3072 kB)
[ 0.000000] .data : 0xc0c00000 - 0xc0c44f40 ( 276 kB)
[ 0.000000] .bss : 0xc0c4a1cc - 0xc0c875a4 ( 245 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] Switching to timer-based delay loop, resolution 41ns
[ 0.000015] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[ 0.000050] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.001950] Console: colour dummy device 80x30
[ 0.002557] console [tty0] enabled
[ 0.002624] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.002680] CPU: Testing write buffer coherency: ok
[ 0.002786] pid_max: default: 32768 minimum: 301
[ 0.003185] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.003240] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.005501] Setting up static identity map for 0x80100000 - 0x80100060
[ 0.007129] devtmpfs: initialized
[ 0.018328] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.018725] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.018801] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.020263] pinctrl core: initialized pinctrl subsystem
[ 0.020470] regulator: Failed to create debugfs directory
[ 0.020900] regulator-dummy: Failed to create debugfs directory
[ 0.022881] NET: Registered protocol family 16
[ 0.024774] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.033700] vdd3p0: Failed to create debugfs directory
[ 0.033779] vdd3p0: supplied by regulator-dummy
[ 0.034330] cpu: supplied by regulator-dummy
[ 0.034636] cpu: Failed to create debugfs directory
[ 0.035163] vddsoc: supplied by regulator-dummy
[ 0.035476] vddsoc: Failed to create debugfs directory
[ 0.051104] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
[ 0.051746] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver
[ 0.078785] 5V: Failed to create debugfs directory
[ 0.079242] 5V: Failed to create debugfs directory
[ 0.079860] USB_OTG1_VBUS: Failed to create debugfs directory
[ 0.080577] USB_OTG2_VBUS: Failed to create debugfs directory
[ 0.081262] VDD_SD2: Failed to create debugfs directory
[ 0.082040] SCSI subsystem initialized
[ 0.082411] usbcore: registered new interface driver usbfs
[ 0.082516] usbcore: registered new interface driver hub
[ 0.082628] usbcore: registered new device driver usb
[ 0.084203] i2c-gpio i2c-gpio: using pins 117 (SDA) and 120 (SCL)
[ 0.085446] i2c i2c-0: IMX I2C adapter registered
[ 0.085515] i2c i2c-0: can't use DMA, using PIO instead.
[ 0.086241] Advanced Linux Sound Architecture Driver Initialized.
[ 0.087493] Bluetooth: Core ver 2.22
[ 0.087595] NET: Registered protocol family 31
[ 0.087630] Bluetooth: HCI device and connection manager initialized
[ 0.087683] Bluetooth: HCI socket layer initialized
[ 0.087718] Bluetooth: L2CAP socket layer initialized
[ 0.087755] Bluetooth: SCO socket layer initialized
[ 0.089122] clocksource: Switched to clocksource mxc_timer1
[ 0.105213] NET: Registered protocol family 2
[ 0.105779] IP idents hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.107158] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.107300] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.107428] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.107642] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.107714] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.108065] NET: Registered protocol family 1
[ 0.108789] RPC: Registered named UNIX socket transport module.
[ 0.108846] RPC: Registered udp transport module.
[ 0.108877] RPC: Registered tcp transport module.
[ 0.108909] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.483070] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.499517] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.501634] NFS: Registering the id_resolver key type
[ 0.501822] Key type id_resolver registered
[ 0.501858] Key type id_legacy registered
[ 0.502345] fuse init (API version 7.26)
[ 0.510644] NET: Registered protocol family 38
[ 0.511265] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 0.511358] io scheduler noop registered
[ 0.511392] io scheduler deadline registered
[ 0.511865] io scheduler cfq registered (default)
[ 0.517536] mxsfb 21c8000.lcdif: 21c8000.lcdif supply lcd not found, using dummy regulator
[ 0.522704] mxsfb 21c8000.lcdif: failed to find mxc display driver
[ 0.556366] Console: switching to colour frame buffer device 100x30
[ 0.578689] mxsfb 21c8000.lcdif: initialized
[ 0.594339] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 18, base_baud = 5000000) is a IMX
[ 0.601284] Console IMX rounded baud rate from 114943 to 114900
[ 0.612866] imx-sdma 20ec000.sdma: loaded firmware 3.3
[ 1.212483] console [ttymxc0] enabled
[ 1.224637] 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 53, base_baud = 5000000) is a IMX
[ 1.241673] 21f4000.serial: ttymxc4 at MMIO 0x21f4000 (irq = 54, base_baud = 5000000) is a IMX
[ 1.260153] tun: Universal TUN/TAP device driver, 1.6
[ 1.272896] CAN device driver interface
[ 1.285705] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator
[ 1.339271] PPP generic driver version 2.4.2
[ 1.351479] usbcore: registered new interface driver awl13
[ 1.364406] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[ 1.379499] usbcore: registered new interface driver pegasus
[ 1.393018] usbcore: registered new interface driver rtl8150
[ 1.406403] usbcore: registered new interface driver r8152
[ 1.419474] usbcore: registered new interface driver lan78xx
[ 1.432469] usbcore: registered new interface driver asix
[ 1.444892] usbcore: registered new interface driver ax88179_178a
[ 1.457916] usbcore: registered new interface driver cdc_ether
[ 1.470685] usbcore: registered new interface driver net1080
[ 1.483173] usbcore: registered new interface driver cdc_subset
[ 1.495671] usbcore: registered new interface driver zaurus
[ 1.507574] usbcore: registered new interface driver cdc_ncm
[ 1.519187] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.531711] ehci-mxc: Freescale On-Chip EHCI Host driver
[ 1.543200] usbcore: registered new interface driver cdc_acm
[ 1.554682] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.568667] usbcore: registered new interface driver usb-storage
[ 1.580756] usbcore: registered new interface driver usbserial
[ 1.592224] usbcore: registered new interface driver usbserial_generic
[ 1.604418] usbserial: USB Serial support registered for generic
[ 1.615959] usbcore: registered new interface driver cp210x
[ 1.627082] usbserial: USB Serial support registered for cp210x
[ 1.638418] usbcore: registered new interface driver ftdi_sio
[ 1.649413] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 1.662140] usbcore: registered new interface driver mxuport
[ 1.673090] usbserial: USB Serial support registered for MOXA UPort
[ 1.684614] usbcore: registered new interface driver pl2303
[ 1.695602] usbserial: USB Serial support registered for pl2303
[ 1.713380] ci_hdrc ci_hdrc.0: EHCI Host Controller
[ 1.724153] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
[ 1.759166] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
[ 1.772232] hub 1-0:1.0: USB hub found
[ 1.782341] hub 1-0:1.0: 1 port detected
[ 1.797750] ci_hdrc ci_hdrc.1: EHCI Host Controller
[ 1.809231] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2
[ 1.849168] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[ 1.862905] hub 2-0:1.0: USB hub found
[ 1.873460] hub 2-0:1.0: 1 port detected
[ 1.885906] udc-core: couldn't find an available UDC - added [g_cdc] to list of pending drivers
[ 1.903232] snvs_rtc 20cc000.snvs:snvs-rtc-lp: registered as rtc0
[ 1.916568] i2c /dev entries driver
[ 1.928567] IR NEC protocol handler initialized
[ 1.939881] IR RC5(x/sz) protocol handler initialized
[ 1.951802] IR RC6 protocol handler initialized
[ 1.963059] IR JVC protocol handler initialized
[ 1.974090] IR Sony protocol handler initialized
[ 1.985141] IR SANYO protocol handler initialized
[ 1.996215] IR Sharp protocol handler initialized
[ 2.007017] IR MCE Keyboard/mouse protocol handler initialized
[ 2.018954] IR XMP protocol handler initialized
[ 2.031820] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
[ 2.044297] usbcore: registered new interface driver btusb
[ 2.056283] sdhci: Secure Digital Host Controller Interface driver
[ 2.068656] sdhci: Copyright(c) Pierre Ossman
[ 2.079054] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.159166] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
[ 2.239555] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
[ 2.264459] mmc0: new DDR MMC card at address 0001
[ 2.277656] usbcore: registered new interface driver usbhid
[ 2.289638] usbhid: USB HID core driver
[ 2.300240] mmcblk0: mmc0:0001 Q2J55L 3.53 GiB
[ 2.311576] mmcblk0boot0: mmc0:0001 Q2J55L partition 1 2.00 MiB
[ 2.331544] Netfilter messages via NETLINK v0.30.
[ 2.342949] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[ 2.355518] nf_tables: (c) 2007-2009 Patrick McHardy
[ 2.368285] nf_tables_compat: (c) 2012 Pablo Neira Ayuso
[ 2.382610] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.395853] NET: Registered protocol family 10
[ 2.408606] mmcblk0boot1: mmc0:0001 Q2J55L partition 2 2.00 MiB
[ 2.421854] mmcblk0gp0: mmc0:0001 Q2J55L partition 4 8.00 MiB
[ 2.435899] mmcblk0gp1: mmc0:0001 Q2J55L partition 5 8.00 MiB
[ 2.449837] mmcblk0gp2: mmc0:0001 Q2J55L partition 6 8.00 MiB
[ 2.462489] mmcblk0gp3: mmc0:0001 Q2J55L partition 7 8.00 MiB
[ 2.474976] mmcblk0rpmb: mmc0:0001 Q2J55L partition 3 4.00 MiB, chardev (248:0)
[ 2.491521] Segment Routing with IPv6
[ 2.501742] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.515236] NET: Registered protocol family 17
[ 2.526110] can: controller area network core (rev 20170425 abi 9)
[ 2.539055] NET: Registered protocol family 29
[ 2.549919] can: raw protocol (rev 20170425)
[ 2.560383] can: broadcast manager protocol (rev 20170425 t)
[ 2.572502] can: netlink gateway (rev 20170425) max_hops=1
[ 2.588666] Bluetooth: RFCOMM TTY layer initialized
[ 2.600085] Bluetooth: RFCOMM socket layer initialized
[ 2.611493] Bluetooth: RFCOMM ver 1.11
[ 2.621354] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 2.632798] Bluetooth: BNEP filters: protocol multicast
[ 2.644055] Bluetooth: BNEP socket layer initialized
[ 2.654956] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 2.666746] Bluetooth: HIDP socket layer initialized
[ 2.677636] Key type dns_resolver registered
[ 2.688334] cpu cpu0: _opp_add: duplicate OPPs detected. Existing: freq: 900000000, volt: 1275000, enabled: 1. New: freq: 900000000, volt: 1275000, enabled: 1
[ 2.714526] cpu cpu0: _opp_add: duplicate OPPs detected. Existing: freq: 792000000, volt: 1225000, enabled: 1. New: freq: 792000000, volt: 1225000, enabled: 1
[ 2.741677] cpu cpu0: _opp_add: duplicate OPPs detected. Existing: freq: 528000000, volt: 1175000, enabled: 1. New: freq: 528000000, volt: 1175000, enabled: 1
[ 2.770513] cpu cpu0: _opp_add: duplicate OPPs detected. Existing: freq: 396000000, volt: 1025000, enabled: 1. New: freq: 396000000, volt: 1025000, enabled: 1
[ 2.800191] cpu cpu0: _opp_add: duplicate OPPs detected. Existing: freq: 198000000, volt: 950000, enabled: 1. New: freq: 198000000, volt: 950000, enabled: 1
[ 2.831070] ThumbEE CPU extension supported.
[ 2.844145] mmcblk0: p1 p2 p3
[ 2.868736] imx_thermal 2000000.aips-bus:tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C
[ 2.892557] mmcblk0gp1:
[ 2.902639] input: gpio-keys as /devices/soc0/gpio-keys/input/input0
[ 2.918456] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01 00:00:01 UTC (1)
[ 2.941479] 5V: disabling
[ 2.950882] ALSA device list:
[ 2.960506] No soundcards found.
[ 2.973467] Warning: unable to open an initial console.
[ 2.991036] Freeing unused kernel memory: 3072K
[ 3.150413] systemd-udevd[83]: starting version 215
[ 3.171853] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 4.362457] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 4.871424] systemd[1]: System time before build time, advancing clock.
[ 4.905462] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 4.947819] systemd[1]: Detected architecture arm.
Welcome to Debian GNU/Linux 10 (buster)!
[ 5.000229] systemd[1]: Set hostname to .
[ 6.518377] random: systemd: uninitialized urandom read (16 bytes read)
[ 6.544791] random: systemd: uninitialized urandom read (16 bytes read)
[ 6.558078] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ OK ] Listening on initctl Compatibility Named Pipe.
[ 6.599667] random: systemd: uninitialized urandom read (16 bytes read)
[ 6.612967] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Started Dispatch Password …ts to Console Directory Watch.
[ 6.665212] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ 6.710098] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ OK ] Started Forward Password R…uests to Wall Directory Watch.
[ 6.759663] systemd[1]: Reached target Local Encrypted Volumes.
[ OK ] Reached target Local Encrypted Volumes.
[ 6.800148] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
[ 6.815595] systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
[ OK ] Listening on Syslog Socket.
[ OK ] Created slice system-getty.slice.
[ OK ] Reached target Paths.
[ OK ] Listening on udev Control Socket.
[ OK ] Listening on fsck to fsckd communication Socket.
[ OK ] Reached target Swap.
[ OK ] Created slice User and Session Slice.
[ OK ] Reached target Slices.
[ OK ] Reached target Remote File Systems.
[ OK ] Set up automount Arbitrary…s File System Automount Point.
[ OK ] Listening on Journal Socket.
Starting Load Kernel Modules...
Starting Journal Service...
Starting Remount Root and Kernel File Systems...
[ OK ] Listening on udev Kernel Socket.
Starting udev Coldplug all Devices...
[ OK ] Started Load Kernel Modules.
Starting Apply Kernel Variables...
[ 7.532212] random: systemd: uninitialized urandom read (16 bytes read)
Mounting Kernel Configuration File System...
[ 7.670760] random: systemd: uninitialized urandom read (16 bytes read)
Mounting FUSE Control File System...
[ 7.812625] random: systemd-journal: uninitialized urandom read (16 bytes read)
[ 7.836359] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ OK ] Mounted Kernel Configuration File System.
[ OK ] Started Remount Root and Kernel File Systems.
[ OK ] Mounted FUSE Control File System.
[ OK ] Started Apply Kernel Variables.
Starting Create System Users...
Starting Load/Save Random Seed...
[ OK ] Started Load/Save Random Seed.
[ OK ] Started Journal Service.
Starting Flush Journal to Persistent Storage...
[ 8.565064] random: systemd-journal: uninitialized urandom read (16 bytes read)
[ OK ] Started Create System Users.
[ 8.661068] random: systemd: uninitialized urandom read (16 bytes read)
Starting Create Static [ 8.732407] random: systemd-journal: uninitialized urandom read (16 bytes read)
Device Nodes in /dev...
[ 8.920111] systemd-journald[155]: Received request to flush runtime journal from PID 1
[ OK ] Started Flush Journal to Persistent Storage.
[ OK ] Started Create Static Device Nodes in /dev.
[ OK ] Reached target Local File Systems (Pre).
[ OK ] Reached target Local File Systems.
Starting netfilter persistent configuration...
Starting udev Kernel Device Manager...
Starting Create Volatile Files and Directories...
[ OK ] Started udev Coldplug all Devices.
[ OK ] Started netfilter persistent configuration.
[ OK ] Reached target Network (Pre).
Starting Helper to synchronize boot up for ifupdown...
[ OK ] Started Helper to synchronize boot up for ifupdown.
Starting Raise network interfaces...
[ OK ] Started udev Kernel Device Manager.
[ OK ] Started Create Volatile Files and Directories.
Starting Update UTMP about System Boot/Shutdown...
Starting Network Time Synchronization...
[ OK ] Started Raise network interfaces.
[ OK ] Reached target Network.
[ OK ] Reached target Network is Online.
[ OK ] Started Update UTMP about System Boot/Shutdown.
[ OK ] Found device /dev/ttymxc0.
[ OK ] Created slice system-systemd\x2dbacklight.slice.
Starting Load/Save Screen …backlight:backlight-display...
[ OK ] Started Network Time Synchronization.
[ OK ] Started Load/Save Screen B…f backlight:backlight-display.
[ OK ] Found device /dev/mmcblk0gp0.
Mounting /opt/license...
[ 14.156704] squashfs: SQUASHFS error: Can't find a SQUASHFS superblock on mmcblk0gp0
[ OK ] Started ifup for eth0.
[ OK ] Reached target System Time Synchronized.
[ OK ] Reached target System Initialization.
[ OK ] Started Daily man-db regeneration.
[ OK ] Started Daily rotation of log files.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Reached target Sockets.
[ OK ] Started Daily apt download activities.
[ OK ] Started Daily apt upgrade and clean activities.
[ OK ] Reached target Basic System.
[ 14.531148] SMSC LAN8710/LAN8720 2188000.ethernet-1:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=2188000.ethernet-1:00, irq=POLL)
Starting /etc/rc.local Compatibility...
[ 14.589379] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Starting Login Service...
Starting System Logging Service...
[ OK ] Started Regular background program processing daemon.
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Reached target Timers.
[ OK ] Started D-Bus System Message Bus.
Starting LSB: exim Mail Transport Agent...
Starting Permit User Sessions...
[ OK ] Started System Logging Service.
[FAILED] Failed to mount /opt/license.
See 'systemctl status opt-license.mount' for details.
[ OK ] Started /etc/rc.local Compatibility.
[ OK ] Started Login Service.
[ OK ] Started Permit User Sessions.
[ OK ] Started Serial Getty on ttymxc0.
[ OK ] Started Getty on tty1.
[ OK ] Reached target Login Prompts.
[ OK ] Started LSB: exim Mail Transport Agent.
[ OK ] Reached target Multi-User System.
[ OK ] Reached target Graphical Interface.
Starting Update UTMP about System Runlevel Changes...
[ OK ] Started Update UTMP about System Runlevel Changes.