U-Boot SPL 2016.07-at11 (May 26 2017 - 10:44:08) Trying to boot from MMC1 U-Boot 2016.07-at11 (May 26 2017 - 10:44:08 +0900) CPU: Freescale i.MX7D rev1.2 996 MHz (running at 792 MHz) CPU: Extended Commercial temperature grade (-20C to 105C) at 29C Reset cause: POR Watchdog enabled I2C: ready DRAM: 512 MiB Boot Source: SD error: BMIC EEPROM detect MMC: FSL_SDHC: 0, FSL_SDHC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Found PFUZE300! deviceid 0x30, revid 0x11 Net: No ethernet found. switch to partitions #0, OK mmc0 is current device switch to partitions #0, OK mmc0 is current device reading boot.scr 200 bytes read in 10 ms (19.5 KiB/s) Running bootscript from mmc ... ## Executing script at 82000000 switch to partitions #0, OK mmc0 is current device reading uImage 10157176 bytes read in 471 ms (20.6 MiB/s) Booting from mmc ... reading x1-minimal.dtb 45493 bytes read in 20 ms (2.2 MiB/s) ## Booting kernel from Legacy Image at 82000000 ... Image Name: Linux-3.14.79-at15 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 10157112 Bytes = 9.7 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 84800000 Booting using the fdt blob at 0x84800000 Loading Kernel Image ... OK Using Device Tree in place at 84800000, end 8480e1b4 Starting kernel ... Booting Linux on physical CPU 0x0 Linux version 3.14.79-at15 (atmark@atde6) (gcc version 4.9.2 ( 4.9.2-10) ) #2 SMP PREEMPT Wed Jun 28 10:29:12 JST 2017 CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine model: Atmark-Techno Armadillo-X1 - minimal configuration cma: CMA: reserved 64 MiB at 9c000000 Memory policy: Data cache writealloc PERCPU: Embedded 8 pages/cpu @9bbb7000 s8576 r8192 d16000 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 Kernel command line: console=ttymxc4,115200 root=/dev/mmcblk0p2 rootwait ro PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 433256K/524288K available (9080K kernel code, 537K rwdata, 8008K rodata, 2572K init, 448K bss, 91032K reserved, 0K highmem) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xa0800000 - 0xff000000 (1512 MB) lowmem : 0x80000000 - 0xa0000000 ( 512 MB) pkmap : 0x7fe00000 - 0x80000000 ( 2 MB) modules : 0x7f000000 - 0x7fe00000 ( 14 MB) .text : 0x80008000 - 0x810b8504 (17090 kB) .init : 0x810b9000 - 0x8133c180 (2573 kB) .data : 0x8133e000 - 0x813c4440 ( 538 kB) .bss : 0x813c444c - 0x8143474c ( 449 kB) SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Preemptible hierarchical RCU implementation. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 NR_IRQS:16 nr_irqs:16 16 Switching to timer-based delay loop sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655765682ns Architected cp15 timer(s) running at 8.00MHz (phys). sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2147483648000ns Ignoring duplicate/late registration of read_current_timer delay Console: colour dummy device 80x30 Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) Initializing cgroup subsys net_cls CPU: Testing write buffer coherency: ok /cpus/cpu@0 missing clock-frequency property /cpus/cpu@1 missing clock-frequency property CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x808a4208 - 0x808a4260 CPU1: Booted secondary processor CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated (12.00 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 pinctrl core: initialized pinctrl subsystem regulator-dummy: no parameters NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations cpuidle: using governor ladder cpuidle: using governor menu Use WDOG1 as reset source syscon 30340000.iomuxc-gpr: regmap [mem 0x30340000-0x3034ffff] registered syscon 30350000.ocotp-ctrl: regmap [mem 0x30350000-0x3035ffff] registered syscon 30360000.anatop: regmap [mem 0x30360000-0x3036ffff] registered vdd1p0d: 800 <--> 1200 mV at 1000 mV vdd1p2: 1100 <--> 1300 mV syscon 30390000.src: regmap [mem 0x30390000-0x3039ffff] registered DDR type is DDR3! hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. hw-breakpoint: maximum watchpoint size is 8 bytes. imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver imx7d-pinctrl 30330000.iomuxc: initialized IMX pinctrl driver MU is ready for cross core communication! bio: create slab at 0 mxs-dma 33000000.dma-apbh: initialized VDD_SD1: 3300 mV vgaarb: loaded i2c-core: driver [max17135] using legacy suspend method i2c-core: driver [max17135] using legacy resume method SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb 30800000.aips-bus:usbphy_nop1 supply vcc not found, using dummy regulator 30800000.aips-bus:usbphy_nop2 supply vcc not found, using dummy regulator i2c i2c-3: IMX I2C adapter registered Linux video capture interface: v2.00 pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered MIPI CSI2 driver module loaded Advanced Linux Sound Architecture Driver Initialized. Bluetooth: Core ver 2.18 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized cfg80211: Calling CRDA to update world regulatory domain Switched to clocksource arch_sys_counter NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 2, 16384 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. imx rpmsg driver is registered. Bus freq driver module loaded futex hash table entries: 512 (order: 3, 32768 bytes) VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered jffs2: version 2.2. (NAND) c 2001-2006 Red Hat, Inc. fuse init (API version 7.22) msgmni has been set to 974 io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) imx-sdma 30bd0000.sdma: no event needs to be remapped imx-sdma 30bd0000.sdma: loaded firmware 4.1 imx-sdma 30bd0000.sdma: initialized pfuze100-regulator 3-0009: Full layer: 1, Metal layer: 1 pfuze100-regulator 3-0009: FAB: 0, FIN: 0 pfuze100-regulator 3-0009: pfuze3000 found. SW1A: 700 <--> 1475 mV at 1100 mV SW1B: 700 <--> 1475 mV at 1000 mV SW2: 1500 <--> 1850 mV at 1800 mV SW3: 900 <--> 1650 mV at 1350 mV SWBST: 5000 <--> 5150 mV at 5000 mV VSNVS: 1000 <--> 3000 mV at 3000 mV VREFDDR: 750 mV VLDO1: 1800 <--> 3300 mV at 1800 mV VLDO2: 800 <--> 1550 mV at 1500 mV VCCSD: 2850 <--> 3300 mV at 3300 mV V33: 2850 <--> 3300 mV at 3300 mV VLDO3: 1800 <--> 3300 mV at 3300 mV VLDO4: 1800 <--> 3300 mV at 3300 mV 30a70000.serial: ttymxc4 at MMIO 0x30a70000 (irq = 62, base_baud = 1500000) is a IMX console [ttymxc4] enabled serial: Freescale lpuart driver imx sema4 driver is registered. [drm] Initialized drm 1.1.0 20060810 [drm] Initialized vivante 1.0.0 20120216 on minor 0 brd: module loaded loop: module loaded (hci_tty): inside hci_tty_init (hci_tty): allocated 248, 0 fsl-quadspi 30bb0000.qspi: Unsupported cmd 0x65 fsl-quadspi 30bb0000.qspi: Unsupported cmd 0x61 fsl-quadspi 30bb0000.qspi: Unsupported cmd 0x65 fsl-quadspi 30bb0000.qspi: n25q064 (8192 Kbytes) 3 ofpart partitions found on MTD device 30bb0000.qspi Creating 3 MTD partitions on "30bb0000.qspi": 0x000000000000-0x000000100000 : "bootloader" 0x000000100000-0x000000140000 : "license" 0x000000140000-0x000000800000 : "reserved" fsl-quadspi 30bb0000.qspi: QuadSPI SPI NOR flash driver CAN device driver interface PPP generic driver version 2.4.2 usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver cdc_eem usbcore: registered new interface driver sierra_net usbcore: registered new interface driver cdc_ncm usbcore: registered new interface driver qmi_wwan ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-mxc: Freescale On-Chip EHCI Host driver usbcore: registered new interface driver cdc_acm cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters usbcore: registered new interface driver cdc_wdm usbcore: registered new interface driver usb-storage usbcore: registered new interface driver usbserial usbcore: registered new interface driver usbserial_generic usbserial: USB Serial support registered for generic usbcore: registered new interface driver ftdi_sio usbserial: USB Serial support registered for FTDI USB Serial Device usbcore: registered new interface driver option usbserial: USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver sierra usbserial: USB Serial support registered for Sierra USB modem usbcore: registered new interface driver usb_serial_simple usbserial: USB Serial support registered for zio usbserial: USB Serial support registered for funsoft usbserial: USB Serial support registered for flashloader usbserial: USB Serial support registered for google usbserial: USB Serial support registered for vivopay usbserial: USB Serial support registered for moto_modem usbserial: USB Serial support registered for hp4x usbserial: USB Serial support registered for suunto usbserial: USB Serial support registered for siemens_mpi 30b10200.usbmisc supply vbus-wakeup not found, using dummy regulator 30b20200.usbmisc supply vbus-wakeup not found, using dummy regulator 30b30200.usbmisc supply vbus-wakeup not found, using dummy regulator mousedev: PS/2 mouse device common for all mice input: 30370000.snvs-pwrkey as /devices/soc/30000000.aips-bus/30370000.snvs-pwrkey/input/input0 snvs_pwrkey 30370000.snvs-pwrkey: i.MX snvs powerkey probed i2c-core: driver [isl29023] using legacy suspend method i2c-core: driver [isl29023] using legacy resume method snvs_rtc 30370034.snvs-rtc-lp: rtc core: registered 30370034.snvs-rtc-l as rtc0 i2c /dev entries driver IR NEC protocol handler initialized IR RC5(x) protocol handler initialized IR RC6 protocol handler initialized IR JVC protocol handler initialized IR Sony protocol handler initialized IR RC5 (streamzap) protocol handler initialized IR SANYO protocol handler initialized IR MCE Keyboard/mouse protocol handler initialized usbcore: registered new interface driver uvcvideo USB Video Class driver (1.1.1) i2c-core: driver [mag3110] using legacy suspend method i2c-core: driver [mag3110] using legacy resume method imx2-wdt 30280000.wdog: timeout 10 sec (nowayout=0) Bluetooth: HCI UART driver ver 2.2 Bluetooth: HCI H4 protocol initialized Bluetooth: HCI BCSP protocol initialized Bluetooth: HCILL protocol initialized Bluetooth: HCIATH3K protocol initialized usbcore: registered new interface driver bcm203x usbcore: registered new interface driver btusb usbcore: registered new interface driver ath3k sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper sdhci-esdhc-imx 30b40000.usdhc: Got CD GPIO #128. sdhci-esdhc-imx 30b40000.usdhc: Got WP GPIO #129. mmc0: no vqmmc regulator found mmc0: SDHCI controller on 30b40000.usdhc [30b40000.usdhc] using ADMA sdhci-esdhc-imx 30b60000.usdhc: allocated mmc-pwrseq sdhci-esdhc-imx 30b60000.usdhc: could not get ultra high speed state, work on normal mode mmc2: no vqmmc regulator found mmc2: no vmmc regulator found mmc2: SDHCI controller on 30b60000.usdhc [30b60000.usdhc] using ADMA caam 30900000.caam: Instantiated RNG4 SH0 caam 30900000.caam: Instantiated RNG4 SH1 caam 30900000.caam: device ID = 0x0a160300 (Era 8) caam 30900000.caam: job rings = 3, qi = 0 mmc0: new ultra high speed SDR104 SDHC card at address 59b4 mmcblk0: mmc0:59b4 USDU1 14.9 GiB mmcblk0: p1 p2 caam algorithms registered in /proc/crypto hmac-sha1-caam alg registration failed sha1-caam alg registration failed hmac-sha224-caam alg registration failed sha224-caam alg registration failed hmac-sha256-caam alg registration failed sha256-caam alg registration failed hmac-md5-caam alg registration failed md5-caam alg registration failed xcbc-aes-caam alg registration failed xcbc-aes-caam alg registration failed caam_jr 30901000.jr0: registering rng-caam snvs-secvio 30370000.caam-snvs: violation handlers armed - non-secure state usbcore: registered new interface driver usbhid mmc2: BKOPS_EN bit is not set usbhid: USB HID core driver usbcore: registered new interface driver r8712u coresight-tmc 30086000.etr: TMC initialized mmc2: new high speed DDR MMC card at address 0001 mmcblk2: mmc2:0001 Q2J55L 3.56 GiB mmcblk2boot0: mmc2:0001 Q2J55L partition 1 2.00 MiB coresight-tmc 30084000.etf: TMC initialized coresight-tpiu 30087000.tpiu: TPIU initialized coresight-funnel 30083000.funnel: FUNNEL initialized coresight-funnel 30041000.funnel: FUNNEL initialized coresight-replicator replicator: REPLICATOR initialized mmcblk2boot1: mmc2:0001 Q2J55L partition 2 2.00 MiB coresight-etm3x 3007c000.etm: ETM initialized coresight-etm3x 3007d000.etm: ETM initialized usbcore: registered new interface driver snd-usb-audio NET: Registered protocol family 26 Netfilter messages via NETLINK v0.30. nfnl_acct: registering with nfnetlink. nf_conntrack version 0.5.0 (7793 buckets, 31172 max) ctnetlink v0.93: registering with nfnetlink. nf_tables: (c) 2007-2009 Patrick McHardy nf_tables_compat: (c) 2012 Pablo Neira Ayuso xt_time: kernel timezone is -0000 ipip: IPv4 over IPv4 tunneling driver gre: GRE over IPv4 demultiplexor driver ip_gre: GRE over IPv4 tunneling driver ip_tables: (C) 2000-2006 Netfilter Core Team ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully arp_tables: (C) 2002 David S. Miller TCP: cubic registered Initializing XFRM netlink socket NET: Registered protocol family 10 mmcblk2rpmb: mmc2:0001 Q2J55L partition 3 4.00 MiB mip6: Mobile IPv6 ip6_tables: (C) 2000-2006 Netfilter Core Team sit: IPv6 over IPv4 tunneling driver ip6_gre: GRE over IPv6 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 Bridge firewalling registered can: controller area network core (rev 20120528 abi 9) NET: Registered protocol family 29 can: raw protocol (rev 20120528) can: broadcast manager protocol (rev 20120528 t) can: netlink gateway (rev 20130117) max_hops=1 Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.11 Bluetooth: BNEP (Ethernet Emulation) ver 1.3 mmcblk2: p1 p2 p3 Bluetooth: BNEP filters: protocol multicast mmcblk2boot1: unknown partition table mmcblk2boot0: unknown partition table Bluetooth: BNEP socket layer initialized Bluetooth: HIDP (Human Interface Emulation) ver 1.2 Bluetooth: HIDP socket layer initialized 8021q: 802.1Q VLAN Support v1.8 Key type dns_resolver registered cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19) ThumbEE CPU extension supported. regulator-dummy: disabling imx mcc test is registered. snvs_rtc 30370034.snvs-rtc-lp: setting system clock to 1970-01-01 00:00:00 UTC (0) ALSA device list: No soundcards found. Warning: unable to open an initial console. Freeing unused kernel memory: 2572K (810b9000 - 8133c000) systemd-udevd[135]: starting version 215 random: systemd-udevd: uninitialized urandom read (16 bytes read, 32 bits of entropy available) EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) EXT3-fs (mmcblk2p2): error: couldn't mount because of unsupported optional features (240) EXT2-fs (mmcblk2p2): error: couldn't mount because of unsupported optional features (240) EXT4-fs (mmcblk2p2): mounted filesystem with ordered data mode. Opts: (null) Mounting proc: failed Starting fsck for root filesystem. EXT4-fs (mmcblk0p2): re-mounted. Opts: data=ordered fsck 1.25 (20-Sep-2001) /dev/mmcblk0p2: clean, 1063/89408 files, 327134/356352 blocks Checking root filesystem: done Remounting root rw: EXT4-fs (mmcblk0p2): re-mounted. Opts: data=ordered done Mounting sysfs: failed Mounting tmpfs on /dev: done Cleaning up system: done Running local start scripts. Creating mtd devnode: done Starting udevd: done Mounting devpts: done Changing file permissions: done Configure /home/ftp: done Starting syslogd: done Starting klogd: done Mounting tmpfs on /tmp, /var/tmp: done Mounting ramfs on /home/ftp/pub: done Setting hostname: done Starting inetd: done Running local start script (/etc/config/rc.local). *+*+* Recovery Start!! *+*+* running === Step.1 Board Update === Board version: 0x0000 Board info: 6640 bytes Erasing flash was unsuccessful. === Step.2 Setup SPI Flash === /images/u-boot-x1-at11.bin: OK random: nonblocking pool is initialized === Step.3 Formatting eMMC === The number of cylinders for this disk is set to 116736. There is nothing wrong with that, but this is larger than 1024, and could in certain setups cause problems with: 1) software that runs at boot time (e.g., old versions of LILO) 2) booting and partitioning software from other OSs (e.g., DOS FDISK, OS/2 FDISK) Command (m for help): Building a new DOS disklabel. Changes will remain in memory only, until you decide to write them. After that the previous content won't be recoverable. The number of cylinders for this disk is set to 116736. There is nothing wrong with that, but this is larger than 1024, and could in certain setups cause problems with: 1) software that runs at boot time (e.g., old versions of LILO) 2) booting and partitioning software from other OSs (e.g., DOS FDISK, OS/2 FDISK) Command (m for help): Command action e extended p primary partition (1-4) Partition number (1-4): First cylinder (1-116736, default 1): Using default value 1 Last cylinder or +size or +sizeM or +sizeK (1-116736, default 116736): Command (m for help): Command action e extended p primary partition (1-4) Partition number (1-4): First cylinder (979-116736, default 979): Using default value 979 Last cylinder or +size or +sizeM or +sizeK (979-116736, default 116736): Command (m for help): Command action e extended p primary partition (1-4) Partition number (1-4): First cylinder (4886-116736, default 4886): Using default value 4886 Last cylinder or +size or +sizeM or +sizeK (4886-116736, default 116736): Using default value 116736 Command (m for help): Partition number (1-4): Hex code (type L to list codes): Changed system type of partition 1 to b (Win95 FAT32) Command (m for help): Partition number (1-4): Hex code (type L to list codes): Command (m for help): Partition number (1-4): Hex code (type L to list codes): Changed system type of partition 3 to b (Win95 FAT32) Command (m for help): The partition table has been altered. Calling ioctl() to re-read partition table mmcblk2: p1 p2 p3 mkfs.vfat 2.11 (12 Mar 2005) Filesystem label= OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) Stride=0 blocks, Stripe width=0 blocks 224000 inodes, 894808 blocks 44740 blocks (5.00%) reserved for the super user First data block=0 Maximum filesystem blocks=918552576 28 block groups 32768 blocks per group, 32768 fragments per group 8000 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736 Allocating group tables: done Writing inode tables: done Creating journal (16384 blocks): done Writing superblocks and filesystem accounting information: done mkfs.vfat 2.11 (12 Mar 2005) Disk /dev/mmcblk2: 3825 MB, 3825205248 bytes 4 heads, 16 sectors/track, 116736 cylinders Units = cylinders of 64 * 512 = 32768 bytes Device Boot Start End Blocks Id System /dev/mmcblk2p1 1 978 31288 b Win95 FAT32 /dev/mmcblk2p2 4886 116736 3579232 83 Linux /dev/mmcblk2p3 979 4885 125024 b Win95 FAT32 Partition table entries are not in disk order === Step.4 Setup Partition === /images/debian-jessie-armhf_ax1_20170808.tar.gz: OK EXT4-fs (mmcblk2p2): mounted filesystem with ordered data mode. Opts: (null) /images/uImage: OK /images/armadillo_x1.dtb: OK === Step.5 sync === *+*+* Recovery Completed!! *+*+* ok System is going down for system reboot now. Starting local stop scripts. Syncing all filesystems: done Unmounting all filesystems: EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) done imx2-wdt 30280000.wdog: Device shutdown: Expect reboot! reboot: System halted U-Boot SPL 2016.07-at11 (May 26 2017 - 10:42:12) Trying to boot from SPI U-Boot 2016.07-at11 (May 26 2017 - 10:42:12 +0900) CPU: Freescale i.MX7D rev1.2 996 MHz (running at 792 MHz) CPU: Extended Commercial temperature grade (-20C to 105C) at 33C Reset cause: POR Watchdog enabled I2C: ready DRAM: 512 MiB Boot Source: QSPI Flash error: BMIC EEPROM detect MMC: FSL_SDHC: 0, FSL_SDHC: 1 SF: Detected N25Q64 with page size 256 Bytes, erase size 64 KiB, total 8 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Found PFUZE300! deviceid 0x30, revid 0x11 Net: No ethernet found. switch to partitions #0, OK mmc1(part 0) is current device switch to partitions #0, OK mmc1(part 0) is current device reading boot.scr ** Unable to read file boot.scr ** reading boot.scr ** Unable to read file boot.scr ** reading uImage 10157176 bytes read in 250 ms (38.7 MiB/s) Booting from mmc ... reading x1-minimal.dtb ** Unable to read file x1-minimal.dtb ** ## Booting kernel from Legacy Image at 82000000 ... Image Name: Linux-3.14.79-at15 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 10157112 Bytes = 9.7 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK FDT and ATAGS support not compiled in - hanging ### ERROR ### Please RESET the board ###